Water Filtration System
REFRIGERATOR CARE
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before Cleaning
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.WARNING
Water Filter Status Light (on some models)
The filter status light will help you know when to change your
water filter. The light will change from green to yellow. This tells
you that it is almost time to change the filter. It is recommended
Explosion Hazard
that you replace the filter when the status light changes to red OR
water flow to your water dispenser or ice maker decreases Use nonflammable cleaner.
noticeably. The filter should be replaced at least every 6 months
Failure to do so can result in death, explosion, or fire.
depending on your water quality and usage.
After changing the filter, reset the filter status light by pressing the
Both the refrigerator and freezer sections defrost automatically.
button. The status light will change from red to green when the However, clean both sections about once a month to avoid build-
system is reset.
up of odors. Wipe up spills immediately.
Non-indicator Water Filter (on some models)IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
If your refrigerator does not have the water filter status light, you thoroughly clean both sections to eliminate odors. To avoid odor
should change the water filter cartridge at least every 6 months transfer and drying out of food, wrap or cover foods tightly.
depending on your water quality and usage. If the water flow to To Clean Your Refrigerator:
the water dispenser or ice maker decreases noticeably before
NOTE: Do not use abrasive or harsh cleaners such as window
6 months have passed, replace the water filter more often.sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated detergents, bleaches or cleansers containing
Changing the Water Filterpetroleum products on plastic parts, interior and door liners or
gaskets. Do not use paper towels, scouring pads, or other harsh
1. Press the eject button to release the filter from the base grille.cleaning tools.
2. Pull the filter straight out.1. Unplug refrigerator or disconnect power.
3. Turn the cap counterclockwise to remove it from the filter.2. Hand wash, rinse, and dry removable parts and interior
IMPORTANT: Do not discard the cap. It is part of your surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
refrigerator. Keep the cap to use with the replacement filter.
3. Wash stainless steel and painted metal exteriors with a clean
4. Align the ridge on the cap with the arrow on the new filter and sponge or soft cloth and a mild detergent in warm water.
turn the cap until it snaps into place.
4. There is no need for routine condenser cleaning in normal
NOTE: You can run the dispenser without a filter. Your water home operating environments. If the environment is
will not be filtered. Simply insert the cap all of the way into the particularly greasy or dusty, or there is significant pet traffic in
base grille and rotate the cap until it is firmly in place.
the home, the condenser should be cleaned every 2 to
5. Remove the protective covers from the O-rings. Be sure the 3 months to ensure maximum efficiency.
O-rings are still in place after the covers are removed.If you need to clean the condenser:
6. Push the filter into the base grille. The eject button will pop
back out when the filter is fully engaged.Remove the base grille.
7. Flush the water system. See ?Water and Ice Dispensers.?Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
Replace the base grille when finished.
5. Plug in refrigerator or reconnect power.
Changing the Light Bulbs
NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the
bulb with one of the same size, shape and wattage. On some
models, the dispenser light requires a heavy duty 10-watt bulb. All
other lights require a 40-watt bulb. Replacement bulbs are
available from your dealer.
1. Unplug refrigerator or disconnect power.
2. Remove light shield when applicable.
NOTE: To clean the light shield, wash it with warm water and
liquid detergent. Rinse and dry the shield well.
3. Remove light bulb and replace with one of the same size,
shape and wattage.
4. Replace light shield when applicable.
5. Plug in refrigerator or reconnect power.
8 |
ACEC
WHIRLPOOL
