Spin Speed selection button
CONSUMPTION DATA Every programme has an automatically preset PROGRAMME START
Verify that the appliance is switched on.
Temperature SelectorLoadWaterEnergy Approx. Programmespin speed.
ProgrammeDurationTurn on the tap and press the ?Start? button.
(°C)(kg)(l)(kWh)(hours : minutes) Press the button to set another spin speed.The indicator lamp of the ?Start? button stops
If spin speed ?0? is selected, the final spin is
Cotton955.060*1.802:05flashing and lights up.
Cotton605.0500.952:05cancelled, but not the intermediate spins.
The programme ends with a drain cycle.Note: If there is a power interruption or if the
Cotton405.0500.602:05appliance is disconnected during the cycle, the
Daily Mixed403.0490.481:00START DELAYprogramme will run again from the point where it
Synthetic602.0560.801:30was interrupted.
The ?Start Delay? button allows the user to run
Synthetic402.0560.401:20the machine at his convenience, for example at END OF WASH CYCLE
Delicate401.5600.550:45
night when electricity is cheaper.
Wool401.0600.500:40 Select programme, spin speed and options. The ?End? lamp of the programme sequence
Silk301.0600.300:50indicator lights up.
Press the ?Start Delay? button several times to
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized 1. Press the ?On/Off? button to switch off the
conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the select a delay time of 1, 3, 6, 9 or 12 hours. machine.
values in the table in relation to the water supply pressure and temperature, the load and the type of wash.The corresponding indicator lamp flashes.
The data on the ?Energy Label? refer to the programme ?Cotton 60°C?.2. Turn the tap off.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains Start the programme (see next paragraph).
the water out.With decreasing delay time the corresponding 3. Wait for the lid to unlock (about 1 minute).
?Rinse Hold? buttonPREPARATION OF WASH CYCLEindicator lamp flashes.4.Open the lid and the drum doors and unload
The laundry remains in the last rinse water without The flashing light of the delay indicator lamp the machine.
1. Load the machine, close the drum doors and
progressing to the final spin cycle to avoid creasing goes out when the programm starts.CHANGE THE PROGRAMME DURING
check that they are properly locked.and prevent colours from fading.The delay time can still be modified after the THE WASH CYCLE
2. Add detergents and additives into the dispenser to This option is particularly recommended for the
?Start? button has been pressed:
no more than the ?MAX? level mark, as follows:?Synthetic?, ?Delicate? and ?Daily Mixed? To decrease the delay time1. Switch the appliance off by pressing ?On/Off?.
Programme with pre and main washprogrammes. (Repeatedly) press the ?Start Delay? button.2. Turn the programme selector knob to the new
Main wash programme without prewash This function is particularly useful if you want to Note, however, that the selected wash programme.
Fabric softeners and conditionerspostpone spinning to a later time, or if you want programme starts IMMEDIATELY as soon as you 3. Switch the appliance on again by pressing
to drain only.?On/Off?. The ?Start? button flashes. If necessary,
Chlorine bleachpush ?Start Delay? with the ?1h? lamp flashing.
As soon as the appliance stops in the rinse hold, To increase the delay timeselect additional options and different spin speed.
Stain remover agentsthe lamp of the ?Start? button flashes.
Anti-scale agents (if necessary) Switch the washing machine off by pushing the 4. Start programme by pressing the ?Start? button.
Appliance in ?Rinse Hold?:?On/Off? button.PAUSE/INTERRUPT A PROGRAMME
3. Press the ?On/Off? button. Press the ?Rinse Hold? button or the flashing
Turn the programme selector to a different
The lamp of the ?Start? button flashes.?Start? button: the programme will terminate programme.If, for any reason, you wish to interrupt the
4. Turn the programme selector knob to the automatically with the selected spin cycle.programme for a certain time and continue it later:
Switch the washing machine on again by
desired programme. The lamp of the If you do not wish to spin the clothes, turn the 1. Press the ?On/Off? button.
programme?s standard spin speed lights up.programme selector knob to the ?Drain? pressing the ?On/Off? button.2. After the desired pause, press again on the
Reselect the desired programme and options.
programme and press the ?Start? button again.?On/Off? button.
SELECT THE DESIRED OPTIONSelect the desired delay time by (repeatedly)
?Intensive Rinse? button
Selecting or deselecting an option can be done The amount of water is increased to ensure a pressing the ?Start Delay? button. Press the CANCEL PROGRAMME
at any time during the programme. The option ?Start? button.1. Switch off the appliance by pressing ?On/Off?.
more intensive rinse.
will be applied as long as the corresponding This option is particularly suitable for areas with 2. Turn the programme selector to ?Drain?.
programme phase has not been executed yet.
very soft water, washing baby linen and people 3. Switch the appliance on again by pressing
with skin allergies.
?On/Off?. The lamp of the ?Start? button
flashes.
4. Press the ?Start? button to start the ?Drain?
programme.
5019 612 10075 |
ACEC
LADEN
