3. Release the belt hook lock lever to lock
3WITCHAND&ORWARD2EVERSELED light How to use the belt hook
the angle of belt hook.
LEVER/PERATIONCAUTION:WARNING:
The built-in LED light is designed to illu-Y Be sure to attach the belt hook
minate the small work area temporarily. securely to the main unit with the screw
Do not use it as a substitute for a regularfirmly fastened. When the belt hook is
flashlight, since it does not have enoughnot firmly attached to the main unit, the4. Make sure the belt hook is firmly
brightness.hook may depart and the main unitlocked.
may fall.
ForwardReverseThis may result in an accident or injury.
Depress the trigger switch, then LED lightTo return the belt hook to the storing posi-
turns on. When the trigger switch istion,
Y Be sure to attach the belt hook firmly
released, the light turns off automatically.Follow step 1. and 2. above, then lower the
and securely onto a waist belt or other
belt hook.
belt. Pay attention to the unit not
The light illuminates with very low current,To secure the lock, follow 3 and 4 above.
slipping off from the belt.
and it does not adversely affect the perfor-
This may result in an accident or injury.
mance of the driver during use or its bat-
To change the belt hook
Switch locktery capacity.Y When the main unit is held by the belt
hook, avoid jumping or running with it.location side
CAUTION:Doing so may cause the hook to slip
The belt hook can be attached to either
To prevent damage, do not operateand the main unit may fall. side of the unit.
Forward/Reverse lever until the bitThis may result in an accident or injury.
comes to a complete stop.
Y When the belt hook is not used, be
sure to return it to the storing position.
&ORWARD 2OTATION 3WITCH
The belt hook may catch on something.
/PERATIONThis may result in an accident or injury.
3XVKWKHOHYHUIRUIRUZDUGURWDWLRQ
Y When the unit is hooked onto the waist
'HSUHVVWKHWULJJHUVZLWFKVOLJKWO\WRbelt by the belt hook, do not attach
driver bits to the unit. 1. Set the belt hook at storing position.
A sharp edge object, such as a drill bit,
7KHVSHHGLQFUHDVHVZLWKWKHDPRXQW2. Loosen the screw turning it counter-
may cause injury or an accident.
RIGHSUHVVLRQRIWKHWULJJHUIRUHIILFLHQWclock-wise, using a coin or a flat blade
WLJKWHQLQJRIVFUHZV7KHEUDNHRSHUscrew driver
To set the belt hook angle
DWHVDQGWKHELWVWRSVLPPHGLDWHO\
ZKHQWKHWULJJHULVUHOHDVHGposition
$IWHUXVHVHWWKHOHYHUWRLWVFHQWHUSR1. Slide the belt hook lock lever # and
VLWLRQ VZLWFKORFN hold it to unlock the belt hook
2EVERSE 2OTATION 3WITCH
$
/PERATION
#
3XVKWKHOHYHUIRUUHYHUVHURWDWLRQ&KHFN
3. Take out the belt hook and insert into
WKHGLUHFWLRQRIURWDWLRQEHIRUHXVH
the other side of the slot on the main
'HSUHVVWKHWULJJHUVZLWFKVOLJKWO\WR
unit
storing position4. Fasten the screw firmly, turning it clock-
$IWHUXVHVHWWKHOHYHUWRLWVFHQWHUSR
wise
VLWLRQ VZLWFKORFN 2. Pull the belt hook from storing position
$ and set it as desired angle
CAUTIONThe belt hook can be taken out from the
main unit only when it is at storing position.
To eliminate excessive temperature
increase of the tool surface, do not oper-
ate the tool continuously (using two or
more battery packs consecutively.) Tool
needs cool off time before switching to
another pack.
� 8 �� 9 � |
ACEC
PANASONIC
