FS-MD9000(J)-e.fm Page 10 Thursday, July 30, 1998 1:19 PM
nYou can place an 8 cm (3'') CD without an adaptor.PROGRAM
nIf the CD cannot be read correctly (because it is scratched, for
example), " 0 0:00" appears on the display.
nYou can insert a CD while listening to the other source.
English
n5.Press the UP, DOWN, >, or < button to
Basics of Using the select the track to program.
CD Player-Normal PlayUP button:Increases the track number by 1.
DOWN button: Decreases the track number by 1.
> button:Increases the tenth digit of the track number.
To Play a CD ????????????
< button:Decreases the tenth digit of the track number.
n1. Insert a CD.? Example: for track 2, press the UP button twice. For track 12,
press the > button, then press the UP button twice (or simply
n2. Press the CD 38 button.
press the UP button 12 times).
The first track of the CD begins playing.
n6.Press the SET button.
Program order number
Track numberPlayback timeUP
? The track number that has been played disappears from the SET(After 2 seconds)
music calender.
? The CD Player automatically stops when the last track of the DOWN
CD has finished playing.
Total playback time of the programmed tracks
To stop playing the CD, press the 7 button.
The following information for the CD is displayed.
n7.Repeat steps 5 and 6 to select the other
tracks for the program.
You can see the total playback time of programmed tracks on
Total track numberTotal playback time
the display. Also, you can see the programmed tracks on the
To stop playing and remove the pr CD,ess the CD0 button to
music calender.
open the CD holder.
To pause, press the 38CD button. The playback time blinkn8.sPr oness the CD 38 button.
the display.The System plays the tracks in the order you have programmed
To cancel pause, press the same button again. Play continuesthem.
from the point where it was paused.nYou can skip to a particular program track by pr4 essing the
or c button during Program Play.
To Select a Track or Passage within nTo stop playing, p7r button once.ess the
To confirm the programmed tracks while the CD player is
a Track ??????????????
stopped, press the 4 or c button; the tracks making up the
During playback, press the 4 or c button to select the track you
program will successively be displayed in the programmed order.
want.
The selected track starts playing.To delete all the tracks in the prog press the ram,7 button re-
peatedly until all the tracks are cleared. Turning off the power or
? 3UHVVýWKHýcýEXWWRQýRQFHýWRýVNLSýWRýWKHýEHJLQQLQJýRIýWKHý
pressing the CD 0 button to open the CD holder will also clear the
QH[WýWUDFNi
? 3UHVVýWKHý4ýEXWWRQýWRýVNLSýWRýWKHýEHJLQQLQJýRIýWKHýWUDFNýEH�programmed tracks.
To exit the program mode on whilce, e the CD Player is
LQJýSOD\HGiý3UHVVýWZLFHýTXLFNO\ýWRýVNLSýWRýWKHýEHJLQQLQJýRIý
stopped, press the PROGRAM button to light off the "CD PRO-
WKHýSUHYLRXVýWUDFNi
GRAM" indicator.
Search Play ????????????Notes:
Holding down the 4 or c button, during playback, will fast for-? If the total playback time of the programmed tracks exceeds 99
ward/backwards the CD so you can quickly find a particular pas-minutes 59 seconds, the total playback time will go out on the
sage in the track you are listening to.
display.
? When the CD contains more than 21 tracks:
Programming the When you try to program a track number exceeding 20 (for
example the 25th track), the total playback time indication will Playing Order of the Tracks
go out, though programming is possible.
You can program the playing order of the tracks using the Remote
Control.To Modify the Program ???????
nYou can program up to 20 tracks in any desired orderModif yincluding the contents o f the program while the CD Player is stopped.
the same tracks.Each time you press the 7 button, the last track in the program is de-
nYou can only make a program when the CD Player is leted. stopped.To add new tracks to the end of the program, repeat above
steps 5 to 7.
n1. Insert a CD.
n2. Press the CD 38 button. Random Play
n3. Press the 7 button to stop the CD.
The tracks will play in no special order when you use this mode.
n4.Press the PROGRAM button.
The System enters the programming mode and the ?CD PRn1. Press theO- RANDOM button on the Remote
GRAM? indicator lights up.Control.
The "CD RANDOM" indicator lights up on the display.
10 |
ACEC
JVC
