SHARP FU-21SE-S Repair Manual

$7.99

SHARP FU-21SE-S - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

Mark Tarkett -

Excellent service, good price, products are excellent. Will do business with this vendor again.

Gary Fisher - 07/25/2006

Excellent! I'm very pleased with quality of Sony DCRDVD-101 owner's manual. The manual has 148 pages and covers basicly everything!. Thanks again for great service!

Roger Mason - 07/28/2006

Man, I was looking for this manual for a while! Where do You get them?;) Of course, quality is goooood:) Anyway, I can only say: A+A+A+!

matt wilschke - 03/07/2008

Essential for popping the top open and cleaning and replacing what needs repalced. One note: the Ornamental Panel is attached with some adhesive as well as screws and faders so don't be shy about prying it open.

John Craig - 07/31/2006

Very nice site and the manual is great. A life-saver. Thank you so much!

Customers who bought this product also purchased

SHARP 14BM CHASSIS Service Manual	SHARP 12P17S Service Manual	SHARP 115U_OM.pdf Service Manual
SHARP 29AS41 Service Manual	SHARP 14BN14 Service Manual	SHARP 14BN1 Service Manual

Click to see text excerpt from the manual

FU-21SE-S
6. Removing the fan7. Removing the thermal fuse ass'y
(1) Loosen the nut and remove the fan.(1) Take out the fan washer T2 from the motor shaft.
Screw-lock is applied to the fan.MOTOR SHAFT
CAUTIONHOLEFAN WASHER T2
When reinstalling the fan after removing it,TEMPERATURE
install it after cleaning the screw-lock appliedFUSE ASS'Y
to the fan, the washer, the motor shaft, etc.
Apply the screw-lock to the motor shaft and
tighten the nut.
When tightening the fan with the nut, evenly
press the center area of the fan and tighten it.
The tightening torque of the nut is 120-160[N.cm].
MOTOR ANGLE
LEAD WIRE COVERMOTOR
(2) Remove the fixing screws (3 pcs.) of the motor
angle and take it out.
(3) Pull out the lead wire cover upward and pull out
the thermal fuse connector (CN-B) from the power
supply PWB.
8. Removing the motor
(1) Pull out the motor connector (CN-C) from the
power supply PWB and take out the motor.
9. Removing the high-voltage unit
Observe the following cautions when replacing the high-voltage unit .
Never touch the discharging part (the surface of ceramic panel) with bare hands.
No dust or oil of your hands for the high-voltage unit. (They may affect the emission of the ion.)
Always hold the case (resin) with clean gloves during replacement.
If you touch the surface or dirt on the surface, clean up with alcohol.
Never forget to unplug the unit before working on it.
Because of turning on the electricity to the electrode, the electrick shock will occur even if the unit is off.
Confirm carefully the connection of the high-voltage harness (the connector 1) and the relay PWB harness
(the connector 2).
(1) Remove the screw (1 pc.) of the cluster guide and take out it from the casing.
(2) Insert a thin plate (ex. metal ruler) between the cluster guide and the high-voltage unit from the connector side.
Push out the high-voltage unit along a thin plate and pull out the connectors 1 and 2.
CAUTION
Do not damage the high-voltage a thin plate harness or the relay PWB harness when inserting a thin plate.
Insert a thin plate from the connector side.
CLUSTER GUIDE
HIGH VOLTAGE UNIT
SCREW
When tightening this screw, support the
boss with your hand in order not to
deform it.
CONNECTOR 1
(HIGH VOLTAGE HARNESS)BOSS
CONNECTOR 2
(RELAY PWB HARNESS)
Install wiring as shown in the figure
15