MIDI Usage ExamplesMIDI Usage Examples
menu has been changed, the indication OStore... ?�message, the most recently received complete(3) Repeat these steps to for other
appears on the display, to allow you to store thebank select instruction (initial values: MSB = 0,program change numbers.
LSB = 0) will be used.
changes.MIDI PCMODE 6/28MIDI PCMODE 6/28
" When the external MIDI device sends only the
!MAPPING MAPPING é6.When the setting is complete, press
program change message without bank select
5.Press the [STORE/SWAP] key to save the [EXIT] key to exit the AMP
MSB and LSB, the same as above applies,
the changes.namely the most recently received completeSELECT/SYSTEM menu.
4.Turn the [TYPE] knob to bring up the
The setting is accepted, and the unit returns tobank select instruction (initial values: MSB = 0,The indication OStore... ?� appears on the display,
?PC MAP? (program change map)
play mode.LSB = 0) will be used.to allow you to store the changes.
parameter.
In the above condition, only the [STORE/SWAP]
and [EXIT] keys are active. By pressing theUsing this display, you can assign any patch of7.Press the [STORE/SWAP] key to save
NOTE
[EXIT] key, you can abort the changes and returnthe G9.2tt to a program change number from 0 �the changes.
When the external MIDI device sends only a bank
to play mode without saving.select message to the G9.2tt, no change occurs.127.The setting is accepted, and the unit returns to
The next time the G9.2tt receives a programplay mode.
6.To send and receive program change change, the most recent bank select instructionProgram change numberIn the above condition, only the [STORE/SWAP]
(+ bank select) messages, connect will be used.key and [EXIT] keys are active. By pressing the
the G9.2tt and the other MIDI device [EXIT] key, you can abort the changes and returnPC MAP PC MAP !Prg: 0Prg: 0
as follows. Using mapping modeto play mode without saving.?Bnk:U0 Bnk:U0 LPat:1 Pat:1
In this mode, a program change map is used toGroup name/bank numberPatch number
assign patches, allowing patches to be specified8.To send and receive program change
 Example for sending program change
by using program change messages only.5.To assign a patch to a program messages, proceed as described in
(+ bank select) messages
change number, proceed as follows.step 6 of ?Using direct mode? (? p.
45).
(1) When a patch at the G9.2tt is switched...NOTE
(2) Program change (+ bank select) messageBefore carrying out the following steps, verify that(1) Turn parameter knob 1 until the
is sentthe send/receive MIDI channel setting of the G9.2ttprogram change number to use is
is as required (? p. 43), and that send/receive ofshown on the top line of the display.Sending and receiving
MIDI OUT MIDI IN
connectorconnectorprogram change messages is enabled (? p. 44).
pedal/switch/key operation
Program change number
1.In play mode, press the [AMP information via MIDI
SELECT/SYSTEM] key.PC MAP PC MAP !Prg: 10Prg: 10
(control change)
?Bnk:U2 Bnk:U2 LPat:1 Pat:1
The G9.2tt allows sending and receiving control
 Example for receiving program change AMP Select 1/28AMP Select 1/28Group name/bank numberPatch number
change messages via MIDI. These messages
(+ bank select) messages!FRONT FRONT
govern actions such as operating the expression
(2) Use parameter knobs 2 and 3 to
pedals 1/2, and switching modules or bypass/mute
(1) When a program change (+ bank select) select the group name/bank number
message is received...2.Turn the [TYPE] knob to bring up the on and off with keys and foot switches. Each
and patch number to assign to the
?MIDI PCMODE? (program change action can be assigned its own control change
MIDI IN MIDI OUT program change number.
connectorconnectormode) parameter.number (CC#).
 Enable control change send/
MIDI PCMODE 6/28MIDI PCMODE 6/28receive
(2) Patch at the G9.2tt is switched.!DIRECT DIRECT The procedure for enabling send/receive of
3.Turn parameter knob 1 to bring up the control change messages is described below.
indication ?MAPPING?.
HINTPC MAP PC MAP !Prg: 10Prg: 10
1.In play mode, press the [AMP
" When the program change mode of the G9.2tt isPatches can now be specified using program?Bnk:A9Bnk:A9éLéLPat:3 Pat:3 é
SELECT/SYSTEM] key.
set to DIRECT, and the external MIDI devicechange messages according to the program
sends only the MSB or LSB of the bank selectchange map.
ZOOM G9.2ttZOOM G9.2tt
4647 |
ACEC
OTHERS
