2 Set the steam control to position O (= no Wait a while before using the button again to avoid
ENGLISHsteam) (Fig. 2).spluttering.
General description (Fig. 1) 3 Tilt the iron backwards.Never direct the steam at people.
A Spray nozzle (GC1830/1820/1815/1814/1730/1720/ 4 Fill the water tank with tap water up to the Vertical steam boost (GC1830/GC1820/
1705) maximum level. (Fig. 3)GC1815/1814 only)
B Filling opening
C Steam controlDo not ll the water tank beyond the MAX indication. 1 The steam boost function can also be used when
-O = no steamDo not put perfume, vinegar, starch, descaling agents, you are holding the iron in vertical position. This is
-l = moderate steam ironing aids or other chemicals in the water tank.useful for removing creases from hanging clothes,
-; = maximum steam curtains, etc (Fig. 9).
, If the tap water in your area is very hard, we advise
-x = Calc-Clean function you to mix it with an equal amount of distilled Never direct the steam at people.
D Spray button T (GC1830/1820/1815/1814/1730/172water or to use distilled water only.
Automatic shut-off (GC1830 only)
0/1705) Setting the temperature
E Steam boost 9 (GC1830/1820/1815/1814) The electronic shut-off function automatically switches
the heating element off if the iron has not been moved
F Automatic shut-off light (GC1830 only) 1 Put the iron on its heel.for a while.
G Temperature light
H Mains cord 2 Set the required ironing temperature by turning the , The auto-off light starts blinking to indicate that the
I Anticalc tablet (GC1830/1820/1730 only)temperature dial to the appropriate position (Fig. 4).iron has been switched off by the safety shut-off
Check the laundry care label for the required ironing function (Fig. 10).
J Type platetemperature:-In horizontal position, this will happen after 30
K Water tank
L Temperature dial1 Synthetic fabrics (e.g. acrylic, viscose, polyamide, seconds.
polyester) -In vertical position, this will happen after 8 minutes.
Important1 Silk , To let the iron heat up again:
2 Wool -Pick up the iron or move it slightly. The auto-off light
Read these instructions for use carefully before using the
appliance and save them for future reference.3 Cotton, linen goes out.
, Check if the voltage indicated on the type plate If you do not know what kind or kinds of fabr-If the temperic an article ature light goes on, wait for it to go out
is made of, determine the right ironing temperature by before you start ironing.
corresponds to the local mains voltage before you ironing a part that will not be visible when you wear or -If the temperature light does not go on, the iron is
connect the appliance.
, If the appliance is provided with an earthed plug, it use the article.ready for use.
must be plugged into an earthed wall socket.Silk, woollen and synthetic materials; iron the reverse side Cleaning and maintenance
of the fabric to prevent shiny patches. Avoid using the
, Do not use the appliance if the plug, the cord or spray function to prevent stains.After ironing
the appliance itself shows visible damage, or if the
appliance has been dropped or is leaking.Start ironing the articles that require the lowest ironing
, Check the cord regularly for possible damage.temperature, such as those made of synthetic bres. 1 Remove the mains plug from the wall socket and let
the iron cool down.
, If the mains cord is damaged, it must be replaced 3 Put the mains plug in an earthed wall socket.
by Philips, a service centre authorised by Philips 2 Wipe scale and any other deposits off the soleplate
or similarly qualied persons in order to avoid a 4 When the temperature light has gone out, wait a with a damp cloth and a non-abrasive (liquid)
hazard.while before you start ironing (Fig. 5).cleaner.
The temperature light will go on from time to time
, Never leave the appliance unattended when it is during ironing.To keep the soleplate smooth, you should avoid hard
connected to the mains.
, Never immerse the iron and the stand, if provided, Using the appliancecontact with metal objects. Never use a scouring pad,
in water.vinegar or other chemicals to clean the soleplate.
Steam ironing
, This appliance is not intended for use by persons 3 Clean the upper part of the appliance with a damp
(including children) with reduced physical, sensory cloth.
or mental capabilities, or lack of experience and 1 Make sure that there is enough water in the water
knowledge, unless they have been given supervision tank. 4 Regularly rinse the water tank with water. Empty
the water tank after cleaning.
or instruction concerning use of the appliance by a 2 Select the recommended ironing temperature (see
person responsible for their safety.chapter Preparing for use, section Setting the Double-Active Calc System
, Children should be supervised to ensure that they temperature).
do not play with the appliance., GC1830/1820/1730: The anti-calc tablet prevents
3 After the temperature light has gone out, set scale from clogging the steam vents. The anti-calc
, The soleplate of the iron can become extremely the steam control to the appropriate steam tablet is constantly active and does not need
hot and may cause burns if touched.
, Do not allow the cord to come into contact with position. Make sure that the steam setting you replacement (Fig. 11).
the soleplate when it is hot.select is suitable for the ironing temperature , The Calc-Clean function removes the scale
selected: (Fig. 6)particles.
, When you have nished ironing, when you clean l for moderate steam (temperature settings 2 to Use the Calc-Clean function once every two weeks. If the
the appliance, when you ll or empty the water
tank and also when you leave the iron even for a 3) water in your area is very hard (i.e. when akes come out
short while: set the steam control to position O, ; for maximum steam (temperature settings 3 to of the soleplate during ironing), the Calc-Clean function
MAX) should be used more frequently.
put the iron on its heel and remove the mains plug The iron will start steaming as soon as the set
from the wall socket. 1 Set the steam control to position O.
, Always place and use the iron and the stand, if temperature has been reached.
provided, on a stable, level and horizontal surface.Ironing without steam 2 Set the temperature dial to MAX.
, This appliance is intended for household use only. 3 Fill the water tank to the maximum level.
1 Set the steam control to position O (= no steam).
Electromagnetic elds (EMF)Do not pour vinegar or other descaling agents into the
This Philips appliance complies with all standards 2 Select the recommended ironing temperature (see water tank.
regarding electromagnetic elds (EMF). If handled chapter Preparing for use, section Setting the
properly and in accordance with the instructions in this temperature). 4 Put the plug in the wall socket.
instruction manual, the appliance is safe to use according Features 5 Unplug the iron when the temperature light has
to scientic evidence available today.gone out.
Spray function (specic types only)
Before first use 6 Hold the iron over the sink and set the steam
You can use the spray function to remove stubborn
1 Remove any sticker or protective foil from the creases at any temperature.control to the Calc-Clean position x. (Fig. 12)
soleplate. 7 Pull the steam control slightly upwards and gently
1 Make sure that there is enough water in the water
2 Let the iron heat up to maximum temperature and tank.shake the iron until all water in the tank has been
pass the iron over a piece of damp cloth for several used up.
minutes to remove any residues from the soleplate. 2 Press the spray button several times to moisten the Steam and boiling water will come out of the soleplate.
article to be ironed (Fig. 7).Scale (if any) will be ushed out.
Note: The iron may give off some smoke when you use it for Steam boost (specic types only) 8 After having used the Calc-Clean function, press
the rst time. This will cease after a short while.
A powerful shot of steam helps to remove stubborn down the steam control while turning it to position
Preparing for usecreases.O.
Repeat the Calc-Clean process if the water coming out of
Filling the water tankThe steam boost function can only be used at the iron still contains scale particles.
temperature settings between 3 and MAX.
Never immerse the iron in water.
1 Press and release the steam boost button (Fig. 8).
1 Make sure the appliance is unplugged.
423000143
2/ |
ACEC
PHILIPS
