This integrated model may be used as an exhaust or filter hood. SinceElectric connection
these instructions cover more than one type of hood within the same
Make sure the supply voltage ratings correspond with those stated on
series, it may be that reference is made to components that do not formthe appliance rating label.
part of the hood that you are installing. lf evacuation is available
This appliances is double insulated do not connect to earth.
(exhaust duct or air flue) we recommend using the hood in the exhaustAttention: If the appliance does not have a plug, when making a fixed
version to discharge all the kitchen vapours and odours outdoors.
in-stallation, a cutoff device must be used to assure omnipolar
disconnection of the mains. The cutoff distance of the contacts must
Exhaust versionbe at least 3 mm.
The hood must be connected by the spigot (supplied as part of the
hood) to a duct to vent all the exhausted air outside the kitchen. OverOperating instructions
horizontal areas, if any, the duct must be slanted out about 10%
The hood should be switched on either before or at the same time as
upwards of the hood in direction towards the outside.cooking or frying commences. Controls (Fig. 8):
Note ? The shorter the exhaust duct is and the fewer bends there are
in it, the more effective will the cooker hood be. When using the exhaustC. Light switch - moving it to the left the lights will turn on.
D. General switch - if the button is in the position of the figure the hood
version, follow these rules: Do not connect the exhaust hood tois turned off - moving it to the left it starts running.
chimneys, flues and air ducts serving the room. Before venting into
E. Speed variator - moving the button to the left the motor speed
exhaust flues and ducts no longer in use, ask for the approval of theincreases and with this the exhaust capacity of the hood.
person or agency responsible for the building. The evacuated air must
not be led into a warm air duct.Note ? When the door is closed, the motor does not run. Leaving the
button D at the left, the button E in connection with speed and opening
the door, the motor will turn on automatically.
Suggestions for using the hood in exhaustNote ? The button E can control either a 3 speed switch or an
positionelectronic speed variator, according to the model.
When an exhaust hood and a heat source requiring ambient air (e.g.
gas, oil, coal stoves, etc.) are used at the same time, attention isMaintenance
required because the air necessary for combustion is exhausted fromNote ? When performing maintenance operations, disconnect the
the room through the hood and this creates depression. There is noplug from the socket. Vapours and odours in the air are exhausted first
such danger when the maximum depression in the room is 0,04 mbar.through the grease filter and then (if the hood is in filter version) through
In this condition no exhaust gas from the heat source is piped. Tothe odour filter. The efficiency of the appliance depends on the
assure this condition, make openings in the room which cannot becondition of the filters.
closed (doors, windows, etc. are not sufficient) and through which the
air necessary for combustion can freely flow.Grease filter
Note ? All the exhaust ductwork in the apartment or house should beThis absorbs vapour-suspendend grease particles and protects the
studied. In case of doubts, get advice or authorization from the personkitchen and furniture from greasy residues. There are three different
or agency responsible for the building. When using gas burners, gastypes:
ovens etc. as well as when using the hood in the filter version, these1. Acrylic - It can be washed at more or less frequent intervals depen-
precautions are not necessary.ding on how often the hood is used. ln any case, it should be washed
every thirty days of hood operation. To do so, wash the filter by hand
Filter versionin warm soapy water (do not wring the filter, press it in a cloth to dry).
2. Special paper (not washable)
This version is used when no exhaust duct to the outdoors is available.
The air is purified by an active vegetable carbon filter and recycled intoWith red diagonal lines on the top of the sheet. Change the filter
when the diagonal lines are visible from below through the grllle
the room. Make sure the carbon odour filter is inserted. The outletholes.
spigot must be connected to a duct which passes through the cabinet
and discharges the filtered air out of the same.3. Aluminium layers
The filter should be washed every 10 - 15 days (in normal operating
Mounting heightconditions). Dip the filter into a degreaser solution or put it in the dish
washer. Make sure not to damage the filter which is made of several
The hood must be fixed centrally above the hob. The minimum distancelayers of thin alloy, by hitting or crushing it.
between the hob and the under part of the hood must be 650 mm.
Note ? The distance, however, is subject to the safety rules in effectActive carbon odour filter
in the various countries. To install the hood please consider the
following dimensions.The exhausted air passes through the active carbon filter and is
cleaned. This filter cannot be washed and must be replaced depending
Wall fixingon how often the hood is used (about twice a year).
Drill 4 holes into the wall and fix the 2 hooking plates P (Fig. 3) with the
dimensions as indicated in fig. 2, then tighten the screws Q (2 for eachChanging the grease and odour filters
The grease filter is placed in the inner of the grille. In order to replace
plate). Put the wall bracket M to the plate hook P. To obtain the requi-
red depth loosen the screws R, let the brackets slide, then tighten theit the grid must be removed. Take off the 2 retaining wires Y which hold
2 screws R. To counterbalance the required depth on the lower side ofit in its place. The filter can be washed or replaced and be fixed to the
grille again. In order to replace the carbon filter Z, it is sufficient turn
the hood, please find a moving spacer H to extract sufficiently after
having loosened the screws G (Fig . 4). After the hood is lined upcounter clockwise. Clean the outside of the hood with a sponge soaked
with liquid neutral detergent or with a cloth soaked with denatured ethyl
correctly, fix again the 2 screws G. For levelling the hood in height use
the screws L (one for each wall bracket M) and tighten or loosen themalcohol. Do not use products containing abrasives.
as needed (Fig. 3).
Substitution of the lamps (Fig. 11)
Mounting of door panelRemove grid A and unlock deflectors B from their seat, replace lamps
Remove the grille A by using the grip F till setting it free, then pull asC and put deflectors back to their initial position. If the lamps fail to light
shown in fig. 5. Not the rear parts of side B of the door with the coursewhen operating the switch, make sure they are screwed in before
calling a technician.
ends 1 (Fig. 6) are visible. Push upwards both course ends till blocking
them and draw the door which is now freed. Mount the wooden panelNote ? The lamps must be only of ?candle? type. Never use lamps
to the boor by putting the self threading screws 2,9x12,7 in their holeswith higher rating than that indicated on the lamp lens.
1 (Fig. 7) without tihtening them. Hang the door together with the panel
on the hood, introducing the upper and lower slides in their seats, closeSafety rules
it and align it with the other cabinets. Tighten the screws in the holesDo not do any flambe cooking underneath the hood. When frying, never
1 and remove once again the door from the hood in order to completeleave the pan alone because the cooking oil could flare up. Clean all the
the fastening of the panel by putting the other self threading screws insurfaces frequently to avoid danger of fire. To do so use a cloth or a
their seats. Remount the door on the hood and push till to the first stop,brush soaked in denatured ethyl alcohol. It is also important to remove
then bring down again both course ends 1 and reassemble the grilleand clean or substitute frequently all filters installed in the hood.
A putting it into the slide N. (Fig. 1) by pushing upwards towards you.
Then pull it down making sure that it fits perfectly into its place. |