Remote control (fig. 19)Replacing lamps and/or starters
a Time setting button 0-30 minutesAfter some time (after a few years in case of normal use) the light
b Start buttonemitted by the tanning lamps will become less bright. When this
c Pause buttonhappens, you will notice a decrease in the tanning capacity of the
d Blinking signalsolarium. You can overcome this problem by setting a slightly longer
e Pilot lamptanning time or by replacing the lamps or by having them replaced.
f Audible signal
g DisplayY You can have the tube lamps and/or starters replaced by an
authorised Philips Service Centre. They have the knowledge and
Y Note that in the following instructions, the buttons to beskills required for this job and the original spare parts for your
used are shown in red. solarium.
Y In the following cases the number 00 will appear on theY If you want to replace the tube lamps and/or starters yourself,
display:you should proceed as follows:
- After you have put the plug in the wall socket;- Unplug the appliance.
- At the end of a tanning session- Remove the decorative caps and undo the screws of the end
- After a power failure.cover at the head of the couch and remove them (fig. 28).
In all these cases, the tanning lamps are out. - Pull the acrylic sheet approx. 10 cm out of the appliance.
- Undo the snap strip on the rear side of the couch, starting at the
- When you put the plug in the wall socket, pilot light e will gohead (figs. 29 and 31).
on (fig. 20). This pilot light will stay on as long as the appliance is- Do the same with the snap strip on the front side of the couch.
connected to the mains. Fully unwind the mains cord.- Remove the acrylic sheet (fig. 31).
Now you can replace the tube lamps and starters.
- First set the time of the tanning session. Push the + button toY NB: You can now also clean the acrylic sheet, if you wish.
put the time forward; push the - button to put the time- To remove the lamps, turn them to the left or to the right so
backward (fig. 21). Keep the button pressed in to adjust the timethat you can lift them out of their holders.
more quickly.
- The lamps and/or starters of the canopy can in principle be
- Switch on the tanning lamps by pressing the start button I (fig.replaced in the same way. In the canopy the starters are located
22).behind the lamps at the head of the canopy. To replace the
starters, you will first have to remove the tube lamps.
Y A blinking signal d will appear; the set time is shown on display
g (25 minutes in this case) (fig. 23). The countdown of the set- Starters can be removed by turning them to the left.
tanning time will now start.
- New lamps and starters and the acrylic sheet are assembled in
Y You can interrupt the tanning session by pressing pause buttonreverse direction and order.
(fig. 24). The tanning lamps will be switched off. You can- Do not forget to fasten the end cover with screws again.
switch them back on again by pressing start button I (fig. 25).
The remaining tanning time will appear on the display.Type HB 578 only: Replacing a lamp of the facial tanner
Y If you want to replace a lamp of the facial tanner (type HB 578
Y You can shorten the set tanning time by first pressing the startonly), proceed as follows:
button I (fig. 26). The tanning lamps are switched off. Set the- Remove the acrylic sheet as indicated above.
new tanning time by means of button a and press start button- Remove the tube lamps on either side of the facial tanner lamp
I.that is to be replaced.
- Type HB 579 only: The HPA lamp of the facial tanner will not
come on immediately, but will start to burn after approx. 3- Pull the lamp downwards and forwards at the sime time to
minutes.remove it from its holder (fig. 32).
- New lamps and starters and the acrylic sheet are assembled in
- During the last minute of the session you will hear an audiblereverse direction and order. Do not forget to fasten the end
signal f (fig. 27). During this minute, the pause function doescover with screws again.
not work.
Type HB 579 only: Replacing the lamp of the facial tanner
Y As soon as the set tanning time has elapsed, the solarium willY The HPA lamp of the facial tanner may only be replaced by
switch off automatically. authorised Philips service personnel.
CleaningThe environment
Y Always unplug the solarium and let it cool down beforeThe lamps of solariums contain substances that can be harmful to
you start cleaning it.the environment. When you discard the lamps, make sure they are
Y You can clean the outside of the solarium with a damp cloth. Benot thrown away with the normal household waste but are handed
careful not to let any water run into the appliance.in at an official collection point.
Y Do not use any scouring agents or scouring pads.
Y Never use abrasive liquids like alcohol, methylated
spirits, petrol or acetone to clean the acrylic sheets: this
could cause irreparable damage.
7 |
ACEC
PHILIPS
