HCD-DP800AV
Inputs
General
GAME IN:voltage 250 mV,
(phono jacks)impedance 47 kilohmsPower requirements
MD/VIDEO IN:voltage 450 mV/250 mV,North American model:120 V AC, 60 Hz
(phono jacks)impedance 47 kilohmsEuropean model:230 V AC, 50/60 Hz
OPTICAL IN:Australian model:230 � 240 V AC,
(Square optical connector jacks, front panel (North50/60 Hz
American and European models only), or front andMexican model:120 V AC, 60 Hz
rear panels (except for North American and EuropeanKorean model:220 V AC, 60 Hz
models))Other models:120 V, 220 V or
MIC:sensitivity 1 mV,230 � 240 V AC,
(Except for Northimpedance 10 kilohms50/60 Hz
American andAdjustable with voltage
European models)selector
(phone jack)Power consumption
OutputsCanadian model:190 VA
MD (VIDEO) OUT:voltage 250 mV170 watts
European model:
(phono jacks)impedance 1 kilohms0.5 watts (during Power
PHONES:accepts headphones ofSaving Mode)
(stereo mini jack)8 ohms or more
Other models:210 watts
FRONT SPEAKERaccepts impedance of 8 to
16 ohmsDimensions (w/h/d)Approx. 280 x 360 x 365 mm
REAR SPEAKER:accepts impedance of 8 to
16 ohmsMass
CENTER SPEAKER:accepts impedance of 8 toNorth American and European models:
16 ohmsApprox. 10.5 kg
SUB WOOFER:Voltage 1 V,
Other models:Approx. 12.0 kg
impedance 1 kilohms
CD player sectionSupplied accessories:AM loop antenna (1)
SystemCompact disc and digitalFM lead antenna (1)
audio systemRemote commander (1)
LaserSemiconductor laserBatteries (2)
(?=660 nm)Front speaker pads (8)
Center and rear speaker
Frequency response2 Hz � 20 kHz (?0.5 dB)
Signal-to-noise ratioMore than 90 dBpads
Dynamic rangeMore than 90 dBDesign and specifications are subject to change
DIGITAL OUT OPTICALwithout notice.
(Square optical connector jack, rear panel)
wavelength660 nm
SAFETY-RELATED COMPONENT WARNING!!
Tape player section
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
Recording system4-track 2-channel stereo
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
Frequency response40 � 13,000 Hz (?3 dB),
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
(DOLBY NR OFF)using Sony TYPE I
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
cassette,
40 � 14,000 Hz (?3 dB),APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
using Sony TYPE IIPUBLISHED BY SONY.
cassette
Tuner sectionATTENTION AU COMPOSANT AYANT RAPPORT
FM stereo, FM/AM superheterodyne tuner� LA S?CURIT?!
LES COMPOSANTS IDENTIF?S PAR UNE MARQUE 0 SUR LES
FM tuner sectionDIAGRAMMES SCH?MATIQUES ET LA LISTE DES PIéCES SONT
CRITIQUES POUR LA S?CURIT? DE FONCTIONNEMENT. NE
Tuning range87.5 � 108.0 MHz
REMPLACER CES COMPOSANTS QUE PAR DES PIéSES SONY
AntennaFM lead antenna
Antenna terminals75 ohm unbalancedDONT LES NUM?ROS SONT DONN?S DANS CE MANUEL OU
Intermediate frequency10.7 MHzDANS LES SUPP?MENTS PUBLI?S PAR SONY.
AM tuner section
Tuning rangeNOTES ON HANDLING THE OPTICAL PICK-UP
Pan American model:530 � 1,710 kHz
BLOCK OR BASE UNIT
(with the interval set at
10 kHz)
531 � 1,710 kHzThe laser diode in the optical pick-up block may suffer electrostatic
(with the interval set atbreak-down because of the potential difference generated by the
9 kHz)
charged electrostatic load, etc. on clothing and the human body.
European and Middle Eastern models:
During repair, pay attention to electrostatic break-down and also
531 � 1,602 kHz
(with the interval set atuse the procedure in the printed matter which is included in the
9 kHz)repair parts.
Other models:531 � 1,602 kHzThe flexible board is easily damaged and should be handled with
(with the interval set at
care.
9 kHz)
530 � 1,710 kHz
(with the interval set atNOTES ON LASER DIODE EMISSION CHECK
10 kHz)
AntennaAM loop antenna
The laser beam on this model is concentrated so as to be focused on
Antenna terminalsExternal antenna terminal
the disc reflective surface by the objective lens in the optical pick-
Intermediate frequency450 kHz
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
2 |
ACEC
SONY
