3gb05376.fm Page 68 Tuesday, July 2, 2002 3:31 PM
a. Water inlet fault (no or insufficient water supply)c. Electrical module fault
For models with a fault display, the ?Water tap? For models with a fault display ?F4? to ?F15? are
indicator is on or the display alternately shows displayed and some or all Spin Speed Selection
?FH?. Switch off the appliance by turning the LEDs are flashing. Switch off the appliance. Select
programme selector to the ?? position and a programme and press the ?Start/Pause? button
unplug it.once again. The programme will continue.
For models with no fault display, the washing For models without a fault display the washing
machine stops in the appropriate step. Switch off machine stops in the appropriate step. Switch the
the appliance and unplug it.appliance first off, then on. The programme will
Check whether:continue.
? the water tap is completely open, and the water If the fault re-occurs, contact After Sales Service
supply pressure is sufficient;(See ?After-Sales Service?).
? the water inlet hose is kinked;d.Water Stop fault (if available)
? the mesh filters are blocked (see ?Care and The ?Water Stop? may have been triggered by:
Maintenance? / ?Water Hose Mesh Filters?);1.too much foam.
? the water inlet hose is frozen.2.a leak in the inlet hose or in the appliance.
Reconnect the appliance to the electrical supply.In this case the pump is switched on
For models with a fault display, reselect the automatically in order to pump the water out.
desired programme and press the ?Start/Pause? For models with a fault display the light of the
button again to continue with the programme (do ?Water Stop? indication is on. The display shows
not add detergent for this programme).?FA? or alternately ?F? and ?A? and the pump is
For models without a fault display continue the running. Switch off the appliance by turning the
programme by pressing the ?On/Off? button again programme selector to the ?? position, unplug
(do not add detergent for this programme).the appliance and make sure that the water tap is
If the fault re-occurs, contact After-Sales Service closed.
(see ?After-Sales Service?).For models without a fault display the washing
b.Draining out faultmachine stops in the appropriate step. Switch off
the appliance, , unplug the appliance and make
For models with a fault display, depending on the
sure that the water tap is closed.
model, the display shows statically or alternately Tilt the appliance forwards carefully to allow the
?FP?. Switch off the appliance by turning the
programme selector to the ?? position and collected water to flow out.
unplug it.Then:
For models with no fault display, the washing 1.plug in the appliance,
machine stops in the appropriate step. Switch off 2.turn the water tap on (if water immediately
the appliance and unplug it.flows into the appliance again, without the
Check whether:appliance being started, close water supply and
call After-Sales Service).
? the drain hose is kinked (see ?Installation
Guide?);For models with a fault display reselect the desired
programme and press the ?Start/Pause? button
? the pump / filter are blocked (see ?Removing the again to continue with the programme (do not add
Filter / Draining Residual Water?);
detergent for this programme).
IMPORTANT: before draining, allow the wash water
to cool down.For models without a fault display continue the
programme by pressing the ?On/Off? button again
? the drain hose is frozen.(do not add detergent for this programme).
Connect the appliance to the electrical supply.
If the fault re-occurs, contact After-Sales Service
For models with a fault display reselect the desired (see ?After-Sales Service?).
programme and press the ?Start/Pause? button
again to continue with the programme (do not add
detergent for this programme).
For models without a fault display continue the
programme by pressing the ?On/Off? button again
(do not add detergent for this programme).
If the fault re-occurs, contact After-Sales Service
(see ?After-Sales Service?).
68
Black process 45.0° 100.0 LPI |