30105747GB.fm Page 2 Wednesday, May 11, 2005 6:25 PM
This option is particularly recommended for the ?Clean Pump?
CONSUMPTION DATA
programme ?Synthetics?, ?Daily? and ?Delicates?.Waste water is not pumped out. Check whether the
Temperature LoadWaterEnergyApprox.
This function is particularly useful if you want to drain hose is kinked or the filter must be cleaned; in
ProgrammeProgrammepostpone spinning to a later time, or if you want the latter case refer to the Instructions for Use
Duration
(°C)(kg)(l)(kWh)(hours : minutes)*to drain only.(?Removing the Filter?).
Cotton955.554**1.902:00Note: The programme stops to ?Rinse Hold? at ?Door Locked?
Cotton605.5491.042:20the time the ?Rinse Hold? light in the programme As long as a washing programme is running, the
Cotton405.0440.602:05sequence indication is on.lamp lights up to show that the door cannot be
Synthetics602.5550.801:30Terminate the ?Rinse Hold? option:opened. When the indication goes off, the door can
Synthetics402.5550.601:20be opened again.
Daily403.0450.501:00 Press the ?Rinse Hold? button again; the
programme will terminate automatically with the PROGRAMME END
Superrapid303.0370.400:30
Delicates301.5600.500:45final spin cycle for the present wash programme. The remaining time is on ?0:00? and all the
Wool301.0600.300:40 If you do not wish to spin the clothes, turn the lights of the programme sequence indication
programme selector knob counterclockwise to are off.
Silk301.0450.300:40
Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in compliance the ?Drain? programme and press the 1. Turn the programme selector to the ?Off/0?
with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the ?Start/Pause? button again when the indication
water supply pressure and temperature, the load and the type of wash.position.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household next to it is flashing.
conditions applicable at that time.2. Close the water tap.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the ?Spin Speed? button
water out.3. Open the door and unload the machine.
Every programme has an automatic predefined
?Easy Ironing? button4. Leave the door ajar to allow the drum to dry out.
ADD DETERGENTS, CLOSE THE DOOR maximum spin speed.
AND SELECT THE PROGRAMME Can be used together with ?Cotton?, CHANGE THE PROGRAMME, OPTIONS
?Synthetics? and ?Daily? programmes to make Press the button to set another spin speed.AFTER PROGRAMME START
Add the detergent as described in the programme
table or in the chapter ?Detergents and Additives? ironing easier. If the spin speed ?0? is selected, the final spinning
1. Press the ?Start/Pause? button to pause the
in the booklet. Increases the water quantity and the clothes are is cancelled but intermediate spin peaks remain programme. The light flashes.
spun very soft.during rinse. The water is drained out only.
1. Turn the programme selector knob to the 2. Select the new programme (with temperature),
desired programme and temperature.?Eco? buttonany options and another spin speed if you want.PROGRAMME START
2. The remaining time display shows the duration The duration of the wash is extended and the Open the tap and press the ?Start/Pause? button. 3. Press the ?Start/Pause? button again. The
of the chosen programme (in hours and temperature reduced to save up to 40% of The indication next to the ?Start/Pause? button new programme continues at the same position
minutes) and after taking some seconds for energy but maintaining good washing results.lights up. The indications show the sequence
where the previous programme was
calculating, the indication of the ?Start/Pause? ?Prewash? buttonreached in the programme. After starting the interrupted. Do not add detergent for this
button is flashing. Only for heavily soiled loads (for example sand, programme, the sequence indication runs from left programme.
3. The programme sequence and the predefined granular dirt) sensible. The cycle time increases to right through Wash, Rinse, Spin.CANCEL (RESET) A RUNNING
spin speed indication corresponding to the approximately 15 min.When the sequence of the programme is finished PROGRAMME BEFORE THE END
selected programme lights up.?Intensive Rinse? buttonthe corresponding indication goes out.
The ?Reset? button cancels a programme before
SELECT ANY DESIRED OPTION More water and a longer time in rinse cycle is RED INDICATIONSthe end.
added.
Selecting any option the indication lights up.
This option is particularly suitable for areas with ?Water Tap Closed? Press the ?Reset? button for at least 3
When the combination of programme, additional seconds. Any existing water is drained out
options and temperature is not possible, the very soft water, washing baby linen and helps The appliance has no or insufficient water supply. before the door can be opened.
people with allergies.Open the water tap; if the indication still lights up,
indication lights switch off automatically. Unsuitable
combinations of options are deselected ?Rinse Hold? buttonrefer to the ?Troubleshooting Guide? in the
Instructions for Use.
automatically. The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.Whirlpool is a registered trademark of Whirlpool USA
5019 301 05747
Black process 45.0° 100.0 LPI |
ACEC
