Lint filter or water container indicator lamp
PREPARING THE LAUNDRYSELECTING A PROGRAMME & OPTIONSDAILY MAINTENANCE & CLEANING
light on:
1. Check that all fastenings are closed and that Programme and Options:Clean the lint filter at the end of every drying
? Is the lint filter clean?
pockets are empty. ? To select a programme, turn the programme cycle:
? Is the water container empty?
2. Turn the articles inside out.selector knob to the required position. The 1. Open the door.
Start/Pause indicator lamp is blinking ? Is the water container correctly positioned?
3. Place laundry loosely in the drum to make 2. Pull the filter upwards.
??, indicating that the cycle needs to be ? Is the heat exchanger clean?
sure it doesn?t become tangled.3. Open the filter.
started.Water droplets underneath the dryer:
Sort laundry as follows:4. Remove lint using a soft brush or your
? To select an option, press the corresponding ? Is the heat exchanger correctly positioned?
A) By care symbols (on the collar or inside fingertips.
button. The indicator light in the button
seam):5. Close the filter.? Has any fluff on the heat exchanger seal
lights up confirming that the selection has
been wiped away?
Suitable for tumble dryingbeen made. 6. Push the filter back into place.
? Has any fluff on the door seal been wiped away?
? Press the option button again to cancel the Empty the water container at the end of every
? Has the water container been positioned
option.drying cycle.
Tumble drying with reduced drying correctly?
intensity only1. Pull the handle to remove the water container.STARTING & COMPLETING A PROGRAMME
All programme sequence indicators blinking:
2. Empty the water container.
Do not tumble dry1. Having selected the desired programme and ? Service call necessary.
3. Replace the water container when empty by
options, press the Start/Pause button.
pushing it completely back in place. AFTER-SALES SERVICE
B) By amount and thickness/weightIf the laundry is not removed at the end of
Whenever the load to be dried exceeds dryer the drying cycle, an automatic anti-crease TROUBLESHOOTING GUIDEIf, after carrying out the above checks the
capacity, separate laundry according to cycle will operate for maximum 60 min. The malfunction persists or appears again, turn the
If a fault occurs, before contacting our After-
weight (e.g. towels from thin underwear).drum rotates at regular intervals, preventing dryer off and call our After-Sales Service (refer to
Sales Service, make the following checks to
C) By type of fabricsthe laundry from creasing.try and remedy the problem:guarantee).
Please specify:
Cotton/linen: Towels, cotton jersey, bed This Anti-Crease cycle can be extended up
Drying takes too long / laundry is not dry enough:
and table linen made of cotton or linen.to 12h when Anti-Crease option has been ? The nature of the fault.
? Was the correct programme selected?
Synthetics/Easy Care: Blouses, shirts, selected.? The dryer type and model.
? Was the inserted laundry too wet (Washing
overalls, etc. made of polyester or polyamide, 2.On completion of the programme, set the ? The service code (the number after the word
programme selector knob to position ?0?. machine spin speed less than 800 rpm?
as well as cotton/synthetic mixes.Service on the adhesive rating plate) on the
When the spinning speed is less than 800
right-hand side when the door is open.
D) By drying levelCHANGING A PROGRAMME
rpm the water container fault may occur
? Your full address and phone number.
? Sort into: iron dry, cupboard dry, etc.during the drying cycle.)?
When changing the programme during the
Do not tumble dry: Woollens, silk, nylon drying cycle, the dryer stops. The Start/Pause ? Is the lint filter dirty (filter indicator lamp on)?
stockings, delicate embroidery, fabrics with
indicator lamp is blinking ??.? Is the heat exchanger dirty? (refer to the
metallic decorations, bulky items such as
Instructions for use)
To operate the new programme, press the
sleeping bags, etc.
Start/Pause button. ? Is the ambient temperature too high?
Important: only use specific indicated dryer-
The dryer does not operate:
safe additives and rinse items that have been INTERRUPTING A PROGRAMME
(after a power failure and/or interruption to
treated with stain remover thoroughly in plenty
To interrupt the dryer during operationthe mains supply, always press the Start/
of water before drying. Only use specific
Pause button).
indicated dryer-safe plastic items and never 1. Set the programme selector knob to
dry rubber or articles contaminated with Airing ??.? Is the plug properly inserted into the mains
vegetable oil in the dryer.electricity socket?
2. Press the Start/Pause button.
Wait at least 5 minutes before opening the ? Is there a power failure?
door to allow the dryer to cool down.? Has the fuse blown?
For your safety the programme stops ? Is the door properly closed?
automatically if you open the door.? Has the programme been selected?
3.To restart, after door opening, close the door
? Has the Start/Pause button been pressed?
and press the Start/Pause button again.
5019 307 00315 |