The dryer does not operate:
PREPARING THE LAUNDRYSELECTING A PROGRAMME & OPTIONSDAILY MAINTENANCE & CLEANING
(after a power failure and/or interruption to
1. Check that all fastenings are closed and that Programme and Options:Clean the lint filter at the end of every drying
the mains supply, always press the Start/
pockets are empty. ? To select a programme, turn the programme cycle:
Pause button).
2. Turn the articles inside out.1. Open the door.
selector knob to the required position. The
? Is the plug properly inserted into the mains
3. Place laundry loosely in the drum to make
Start/Pause indicator lamp is blinking 2. Pull the filter upwards.
electricity socket?
sure it doesn?t become tangled.
??, indicating that the cycle needs to be 3. Open the filter.
Sort laundry as follows:? Is there a power failure?
started.
A) By care symbols (on the collar or inside 4. Remove lint using a soft brush or your ? Has the fuse blown?
seam):? To select an option, press the corresponding fingertips.
? Is the door properly closed?
button. The indicator light in the button 5. Close the filter.
Suitable for tumble dryinglights up confirming that the selection has ? Has the programme been selected?
6. Push the filter back into place.
been made. ? Has the Start/Pause button been pressed?
Empty the water container at the end of every
Tumble drying with reduced drying ? Press the option button again to cancel the Lint filter or water container indicator lamp
drying cycle.
intensity onlyoption.light on:
1. Pull the handle to remove the water
STARTING & COMPLETING A PROGRAMME? Is the lint filter clean?
Do not tumble drycontainer.
? Is the water container empty?
1. Having selected the desired programme and 2. Empty the water container.
B) By amount and thickness/weightoptions, press the Start/Pause button.? Is the water container correctly positioned?
3. Replace the water container when empty by
Whenever the load to be dried exceeds dryer ? Is the heat exchanger clean?
If the laundry is not removed at the end of pushing it completely back in place.
capacity, separate laundry according to the drying cycle, an automatic anti-crease
Water droplets underneath the dryer:
weight (e.g. towels from thin underwear).cycle will operate for maximum 60 min. The DRAINAGE SYSTEM
? Is the heat exchanger correctly positioned?
C) By type of fabricsdrum rotates at regular intervals, The 6 kg cotton programmes are made for
? Has any fluff on the heat exchanger seal
Cotton/linen: Towels, cotton jersey, bed preventing the laundry from creasing.matching a 6 kg washed load of cotton spun at
been wiped away?
and table linen made of cotton or linen.This Anti-Crease cycle can be extended up more than 1000 rpm. With a 6 kg load spun at
to 12h when Anti-Crease option has been ? Has any fluff on the door seal been wiped
Synthetics/Easy Care: Blouses, shirts, lower speed than 1000 rpm, we recommend to
away?
selected.
overalls, etc. made of polyester or polyamide, connect your dryer to an external drainage hose
2. On completion of the programme, set the ? Has the water container been positioned
as well as cotton/synthetic mixes.for direct water drainage to avoid water
programme selector knob to position ?0?. correctly?
container emptying.
D) By drying level
CHANGING A PROGRAMMEThis is also valid for testing according the All programme sequence indicators blinking:
? Sort into: iron dry, cupboard dry, etc.
standard IEC/EN 61121.? Service call necessary.
Do not tumble dry: Woollens, silk, nylon When changing the programme during the
stockings, delicate embroidery, fabrics with drying cycle, the dryer stops. The Start/Pause TROUBLESHOOTING GUIDEAFTER-SALES SERVICE
metallic decorations, bulky items such as indicator lamp is blinking ??.
If a fault occurs, before contacting our If, after carrying out the above checks the
sleeping bags, etc.To operate the new programme, press the After-Sales Service, make the following malfunction persists or appears again, turn the
Important: only use specific indicated dryer-Start/Pause button.checks to try and remedy the problem:dryer off and call our After-Sales Service (refer to
safe additives and rinse items that have been guarantee).
INTERRUPTING A PROGRAMMEDrying takes too long / laundry is not dry
treated with stain remover thoroughly in plenty enough:Please specify:
of water before drying. Only use specific To interrupt the dryer during operation? The nature of the fault.
? Was the correct programme selected?
indicated dryer-safe plastic items and never 1. Set the programme selector knob to
? Was the inserted laundry too wet? ? The dryer type and model.
dry rubber or articles contaminated with Airing ??.
? Is the lint filter dirty (filter indicator lamp ? The service code (the number after the word
vegetable oil in the dryer.2. Press the Start/Pause button.
on)?Service on the adhesive rating plate) on the
Wait at least 5 minutes before opening the ? Is the heat exchanger dirty (refer to the right-hand side when the door is open.
door to allow the dryer to cool down.Instructions for use)?? Your full address and phone number.
For your safety the programme stops ? Is the ambient temperature too high?
automatically if you open the door.
3. To restart, after door opening, close the
door and press the Start/Pause button
again.
5019 307 00320 |
ACEC
