Troubleshooting Guide
Tips and advice Before starting a wash programme, Crockery still dirty after washing:
Arrange crockery so that items do nomat ke sure that the spray arms can turn Was the crockery loaded properly?
AFTER-SALES
touch each other. Arrange large freely and are not impeded by crockery
Crockery must be loaded facing
crockery in the lower rack and smallor cuer tlery.SERVICE
downwards; this is important, especially
crockery in the upper rack. Only switch off the dishwasher once the
for large items of crockery.
If after carrying out the above checks
Load cups at an angle to facilitate? Star?t indicator lamp has switched off.
The water jets must spray the entire
water drainage.If the dishwasher is switched off during a the malfunction persists or appears
surface of all items.again, turn the appliance off and turn
Generally speaking, place cutlery inwash the cycle, when switched on again it
crockery and cutlery off the water suare pply tap, then call
basket with the handles positioned will resume the cycle from where it wMake sure thatas
our After-Sales Service (see guarantee).
downwards, but ensure that any sharinterrupp ted without having to start it arranged properly.
Please specify:
knives and forks that might cause again. Have you selected the correct programme?
The nature of the fault.
injury are placed in the basket with the
Did you use too much or too little detergent?
handles positioned upwards.(The use of poor quality detergents may The appliance type and model.
Make sure the water jet can reach all result in less effective washing). The service code (the number after
If a fault occurs, before contacting our
loaded items and that the spray arms the word Service on the adhesive
After-Sales Service, make the followi ng Are the filters clogged or incorrectly
turn freely.rating plate) inside the door
checks to try and remedy the problem:assembled? (See ?Care and Maintena?nce on the right-hand side.
ImportantThe dishwasher is not working:
chapter in the user instructions).
Fill the detergent dispenser and ch Ieck s the plug properly inserted in the wall
Are the spray arms blocked or the nozzles
the salt and rinse aid level. socket?
clogged? (See ?Care and Maintenan? ce
Do not use the appliance for items Is tnot here a power failure?
chapter in the user instructions).
suitable for washing in a dishwash er, Is the dishwasher switched on?
full address and telephone
for example: wooden items, aluminium,Ha s the Start button been pressed?Is the lower spray arm correctly fitte Your d?
number.
plastic utensils, tin, hand-decora tHaeds th e delayed start timer been set Is the salt container cap (water softening
crockery (unglazed), silver cutlery.(if fitted)?system) screwed down?
Do not put liquid fat in the dishwasheIs thr e water supply tap on? Marked crockery:
(e.g. oil used for frying) or cand leIs w thax.e flow of water obstructed by
Is the water hardness level selector not
If a fault occurs or you wish to change impurities? If so, close the water supply
properly adjusted? Se?File (ling the salt
the current programme, press the tap, detach the water hose and clean the
containe? ir n the user instructions).
?START ? button for about 5 seconds untifiltl er. Then re-connect the water hose to
Is the salt container empty? (See ?Filling the
the Start indicator lamp switches off.the tap and open the water tap once
again.salt contai? inern the user instructions).
If regeneration salt is to be added,
Are the filters clogge?Cad? (Sre ee
immediately start a wash programme Was too little detergent used? (See
and Maintenance? chapter in the user
in order to eliminate any residual salt ?Filling the detergent di? inspe thnsee r
instructions).
(rinsing alone is not sufficient).user instructions).
Is the door closed properly?
Sometimes even though the Marked glasses and cutlery:
Is a fault indicated?
regeneration salt container has been Was too much rinse aid used? (See
(The Start indicator lamp flashes).
filled, the corresponding indicator lamp
Start the programme again from the ?Filling the rinse aid di? inspe thnsee r
(if fitted) will light up during the first user instructions).
beginning: press the Start button for
wash cycle after filling with salt.
about 5 seconds, until the Start Noteindica: with some tor models, when the Start button
lamp switches off.is pressed a pre-wash cycle precedes the
Select a new programme and press tactuhe al wash programme; this regenerates the
Start button.water softening system.
Please read the user instructions carefully. |
ACEC
