? Is the door properly closed?
PREPARING THE LAUNDRYSELECTING A PROGRAMME & OPTIONSDAILY MAINTENANCE & CLEANING
? Has the programme been selected?
1. Check that all fastenings are closed and that Programme and Options:Clean the lint filter at the end of every drying
? Has the Start/Pause button been pressed?
pockets are empty. ? To select a programme, turn the programme cycle:
Lint filter or water container indicator lamp
2. Turn the articles inside out.selector knob to the required position. The 1. Open the door.
light on:
3. Place laundry loosely in the drum to make Start/Pause indicator lamp is blinking, 2. Pull the filter upwards.
sure it doesn?t become tangled.?? indicating that the cycle needs to be 3. Open the filter.? Is the lint filter clean?
Sort laundry as follows:started.4. Remove lint using a soft brush or your ? Is the water container empty?
A) By care symbols (on the collar or inside fingertips.? Is the water container correctly positioned?
? To select an option, press the corresponding
seam):? Is the heat exchanger clean?
button. The indicator light in the button 5. Close the filter.
lights up confirming that the selection has Water droplets underneath the dryer:
Suitable for tumble drying6. Push the filter back into place.
been made. Empty the water container at the end of every ? Is the heat exchanger correctly positioned?
? Press the option button again to cancel the drying cycle.? Has any fluff on the heat exchanger seal
Tumble drying with reduced drying
option.1. Pull the handle to remove the water container.been wiped away?
intensity only
2. Empty the water container.? Has any fluff on the door seal been wiped away?STARTING & COMPLETING A PROGRAMME
Do not tumble dry3. Replace the water container when empty by ? Has the water container been positioned
1. Having selected the desired programme and correctly?
pushing it completely back in place.
B) By amount and thickness/weightoptions, press the Start/Pause button.
All programme sequence indicators blinking:
Whenever the load to be dried exceeds dryer If the laundry is not removed at the end of DRAINAGE SYSTEM
? Service call necessary.
capacity, separate laundry according to the drying cycle, an automatic anti-crease The 6 kg cotton programmes are made for
weight (e.g. towels from thin underwear).cycle will operate for maximum 60 min. The AFTER-SALES SERVICE
matching a 6 kg washed load of cotton spun at
C) By type of fabricsdrum rotates at regular intervals, preventing
more than 1000 rpm. With a 6 kg load spun at
If, after carrying out the above checks the
Cotton/linen: Towels, cotton jersey, bed the laundry from creasing.lower speed than 1000 rpm, we recommend to
malfunction persists or appears again, turn the
and table linen made of cotton or linen.
This Anti-Crease cycle can be extended up connect your dryer to an external drainage hose
Synthetics/Easy Care: Blouses, shirts, dryer off and call our After-Sales Service (refer to
to 12h when Anti-Crease option has been for direct water drainage to avoid water
guarantee).
overalls, etc. made of polyester or polyamide,
selected.container emptying.
as well as cotton/synthetic mixes.Please specify:
2.On completion of the programme, set the This is also valid for testing according the
D) By drying level? The nature of the fault.
programme selector knob to position ?0?. standard IEC/EN 61121
? Sort into: iron dry, cupboard dry, etc.? The dryer type and model.
Do not tumble dry: Woollens, silk, nylon CHANGING A PROGRAMME? The service code (the number after the word TROUBLESHOOTING GUIDE
stockings, delicate embroidery, fabrics with Service on the adhesive rating plate) on the
When changing the programme during the If a fault occurs, before contacting our After-
metallic decorations, bulky items such as drying cycle, the dryer stops. The Start/Pause Sales Service, make the following checks to right-hand side when the door is open.
sleeping bags, etc.? Your full address and phone number.
indicator lamp is blinking ??.try and remedy the problem:
Important: only use specific indicated dryer-
Drying takes too long / laundry is not dry enough:
safe additives and rinse items that have been To operate the new programme, press the
? Was the correct programme selected?
treated with stain remover thoroughly in plenty Start/Pause button.
? Was the inserted laundry too wet?
of water before drying. Only use specific
INTERRUPTING A PROGRAMME
indicated dryer-safe plastic items and never ? Is the lint filter dirty (filter indicator lamp on)?
dry rubber or articles contaminated with To interrupt the dryer during operation? Is the heat exchanger dirty? (refer to the
vegetable oil in the dryer.1. Set the programme selector knob to Airing.Instructions for use)
? Is the ambient temperature too high?
2. Press the Start/Pause button.
The dryer does not operate:
Wait at least 5 minutes before opening the
(after a power failure and/or interruption to
door to allow the dryer to cool down.
the mains supply, always press the Start/
For your safety the programme stops Pause button).
automatically if you open the door.
? Is the plug properly inserted into the mains
3.To restart, after door opening, close the door
electricity socket?
and press the Start/Pause button again.
? Is there a power failure?
? Has the fuse blown?
5019 307 00327 |
ACEC
