COMPONENTS
PE-2628B-A,PE-2628K-A
1.Main unit-----------110.Ground lead(BLK:1.5m)854-6424-011
2.DC-DC converterEE-1236B-A111.Parts bag for DC-DC converter -----------1
3.Rmote controllerRCB-169-600111-1. Mounting bracket300-7362-022
4.Battery(CR2025)-----------111-2. Terminal cover345-7403-001
5.Strap300-4976-00111-3. Tapping screw700-5016-894
6.Universal MTG-bracket300-9035-01111-4. Machine screw(M5x8)714-4008-894
7.Outer escutcheon370-6116-00111-5. Plate nut725-0216-004
8.16-Pin extension lead(1.5m) 854-6428-00112.Parts bag for source unit-----------1
(Fuse 3A120-0030-001 )12-1. Hook plate330-8216-032
9.Memory B/U lead(YEL:3.5m) 854-6423-01112-2. Lead holder335-0833-031
(Fuse 10A060-0057-561 )12-3. Hexagonal screw(M5x8)716-0496-011
CAUTIONS
Use of controls, adjustment or performance of proceduresMODEL
other than those specified herein, may result in hazardous12V GROUND
AM 530-1710kHz/FM 87.9-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
radiation exposure.OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
The COMPACT DISC player should not be adjusted or re-(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
paired by anyone except properly qualified service person-THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR
SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.
CLARION CO.,LTD.
nel.50 KAMITODA,TODA-SHI,SAITAMA-KEN,JAPAN
MANUFACTURED:
Clarion Co.,Ltd.
PE-MADE IN Bottom View of DRZ9255SERIAL No.
To engineers in charge of repair or in-
spection of our products.
4. Caution in removal and making wiring connection to the
parts for the automobile.
Before repair or inspection, make sure to follow the
Disconnect the battery terminal after turning the ignition
instructions so that customers and Engineers in
key off. If wrong wiring connections are made with the
charge of repair or inspection can avoid sufferingbattery connected, a short circuit and/or fire may occur. If
any risk or injury.extensive damage is caused due to negligence of repair,
1. Use specified parts.the legal responsibility shall be with the repairing company.
The system uses parts with special safety features against5. Cautions regarding chips.
fire and voltage. Use only parts with equivalent character-Do not reuse removed chips even when no abnormality is
istics when replacing them.observed in their appearance. Always replace them with
The use of unspecified parts shall be regarded as remod-new ones. (The chip parts include resistors, capacitors,
eling for which we shall not be liable. The onus of productdiodes, transistors, etc). The negative pole of tantalum
liability (PL) shall not be our responsibility in cases wherecapacitors is highly susceptible to heat, so use special care
an accident or failure is as a result of unspecified partswhen replacing them and check the operation afterwards.
being used.6. Cautions in handling flexible PWB
2. Place the parts and wiring back in their original positionsBefore working with a soldering iron, make sure that the
after replacement or re-wiring.iron tip temperature is around 270 . Take care not to ap-
For proper circuit construction, use of insulation tubes,ply the iron tip repeatedly(more than three times)to the
bonding, gaps to PWB, etc, is involved. The wiring connec-same patterns. Also take care not to apply the tip with force.
tion and routing to the PWB are specially planned using7. Turn the unit OFF during disassembly and parts replace-
clamps to keep away from heated and high voltage parts.ment. Recheck all work before you apply power to the unit.
Ensure that they are placed back in their original positions8. Cautions in checking that the optical pickup lights up.
after repair or inspection.The laser is focused on the disc reflection surface through
If extended damage is caused due to negligence duringthe lens of the optical pickup. When checking that the la-
repair, the legal responsibility shall be with the repairingser optical diode lights up, keep your eyes more than 30cms
company.away from the lens. Prolonged viewing of the laser within
3. Check for safety after repair.30cms may damage your eyesight.
Check that the screws, parts and wires are put back se-9. Cautions in handling the optical pickup
curely in their original position after repair. Ensure for safetyThe laser diode of the optical pickup can be damaged by
reasons there is no possibility of secondary ploblems aroundelectrostatic charge caused by your clothes and body. Make
the repaired spots.sure to avoid electrostatic charges on your clothes or body,
If extended damage is caused due to negligence of repair,or discharge static electricity before handling the optical
the legal responsibility shall be with the repairing company.pickup.
DRZ9255
- 2 -
HX-D2 |
ACEC
