Suspension and steering 10Y13
19.12 Undo the screw (arrowed) and20.2 Manual choke control knob and its20.3 Removing the manual choke control
withdraw the Passive Anti-Theft Systemlocating lug (arrowed)assembly retaining collar
(PATS) transceiver from the ignition
switch/steering lock barrelkey and turn it to position OI�. Grip the steeringfixing), using a suitable tool to locate in the
wheel each side, then pull and withdraw itcollar recesses (see illustration).
8 Turn the steering wheel as necessary sofrom the column shaft.4 Remove the two screws securing the upper
that one of the air bag module retaining boltssteering column shroud from above, and the
becomes accessible from the rear of theRefittingtwo screws securing it from below, the latter
steering wheel. Undo the bolt, then turn accessible only with the lower shroud
All models
the steering wheel again until the second boltremoved.
15 Refit in the reverse order of removal.
is accessible. Undo this bolt also.5 Disconnect the wiring multi-plugs from the
Make sure that the wheel is centralised, as
9 Withdraw the air bag module from the
noted on removal and turn the ignition key sosteering column multi-function switch
steering wheel far enough to access the
assembly, then remove the single screw
wiring multi-plug. Some force may be neededthat it is in position OI� (steering unlocked).
Tighten the retaining bolt to the specifiedsecuring the multi-function switch assembly
to free the module from the additional steeringto the steering column lock housing. This
torque setting.
wheel spoke retainers.
retaining screw is located directly forward of
10 Disconnect the multi-plug from the rear of
the hazard warning light switch (see
the module, and remove the module from the
20 Steering column (manualillustration). Remove the multi-function
vehicle.
steering) - switch assembly.
Warning: Position the air bag3
removal and refitting6 Disconnect the ignition switch wiring multi-
module in a safe place, with the
plug connector and remove the loom plate
mechanism facing downwards
from its location on the left-hand side of the
as a precaution againstRemoval
steering column (see illustration).
accidental operation.
7 Unclip the bonnet release cable abutment
11 Release the wiring harness from the sideModels without air bag
from its location in the steering column lock
of the steering column and disconnect the air1 Disconnect the battery negative (earth) lead
housing, then detach the cable from the
bag module wiring multi-plug (yellow lead).(refer to Chapter 5A, Section 1).
bonnet release lever by aligning the cable
12 Where applicable, undo the single screw2 Remove the manual choke control knob,
and withdraw the Passive Anti-Theft Systemwhere fitted, by depressing the lug securing it,core with the slot on the release lever and
withdrawing it through that slot. Detach the
(PATS) transceiver from the ignitionand pulling it from its shaft (see illustration).
switch/steering lock barrel (see illustration).The lug is found on the side of the controlspring from the release lever arms, then
disengage the arms from the steering column
13 Turn the steering wheel so that theknob shank.
roadwheels are in the straight-ahead position,3 Remove the lower steering column shroudlock housing and remove the bonnet release
then remove the ignition key to lock theby undoing its four retaining screws, thenlever (see illustration).
steering.detach the choke warning light switch/pull
14 Unscrew the retaining bolt from the centrecontrol assembly from the lower shroud by
of the steering wheel, then insert the ignitionunscrewing its retaining collar (bayonet-type
10
20.7 Bonnet release lever and cable
A Bonnet release cable abutment
B Bonnet release cable slot on release lever
20.5 Steering column multi-function20.6 Removing ignition loom plate fromC Bonnet release lever return spring
switch retaining screw (arrowed) (steeringsteering column lock housing (steeringD Steering column to mounting bracket
wheel removed for clarity)wheel removed for clarity)retaining nuts
1595Ford Fiesta Remake |
ACEC
