CUC 2021Allgemeiner Teil / General Section
Service and Special Functions
1. Switching-on Options3. Picture Settings
1.1 ATS Reset (Automatic Tuning System)Basic Adjustment
Press the power "ON" button while pressing button 3 on the RemoteCall up the picture settings menu with the red button (eye). Via the
Control �> LANGUAGE SELECTION �> OK.menu guide it is possible to change the contrast, picture sharpness and
The ATS system stops at every station of acceptable reception qualitytint (only NTSC sources).
(AFC and coincidence) and stores the station data and the respectiveThe analog values for contrast, picture sharpness and tint are stored
standard automatically (data is stored immediately in the NVM). Theautomatically when leaving the menu.
system then continues searching.
Pressing the "TXT" button stops the ATS function.
4. Open Service Settings
1.2 Loading the Average Values / Emergency Data Set (ROM Data)
4.1 Maximum Programme Number (reversing point)
Call up the programme number which is to be the highest selectablePress and hold the q button on the Remote Control and switch on with
the mains button. After replacement of IC82005 (NVM) for example,
programme position. With button "6" select the dialog line "MANUALthe TV set is started with the emergency data set.
TUNING" via the "DIALOG CENTER". Following the menu guide, enterIn doing so, the basic data is read out from the ROM of processor
"00" in the dialog line. Confirm with "OK" and terminate the menu. AfterIC81050 and loaded into the NVM IC82005:
this setting only those programme positions can be selected with the
IC82005: (data specific to the TV can be set via the Dialog Center):w or q buttons in Programme Mode which are lower than the "00"
- chroma and audio standardsposition.
- decoder settingsWhen setting the reversing point to a programme position L 10, only
- reversing pointsingle-digit selection of the programmes will be possible.
- station ident on/off
4.2 AFC Control- OSD position
The two used programme positions before the reversing point are
provided with an AFC control (video recorder via RF).- blue screen on/off, black screen on/off
- ATS reset
- Hotel Mode on/off4.3 Decoder P1�99
- AGC and AFCBy pressing button "6" call up the dialog line "Decoder (P1-99)" via
- economy switch"DIALOG CENTER" �> "OK" �> "SERVICE" �> "OK". With the 3 or 4
- type of picture tubebutton it is possible to set or reset the decoder bit in the EEPROM for
- analog values (volume, brightness etc.)all programme positions.
- picture sharpness"Manual" indicates that the decoder is set to "on" for at least one
- security on/offprogramme position. Setting the bit for individual programmes, please
- geometry adjustmentsee 2.5.
- programme data (channel finetuning, station ident)
4.4 Forced Chroma Switching
Subsequently enter your personal values, picture geometry via theCall up the dialog line "Color" via "DIALOG CENTER" �> "OK"
Dialog Center.�> "SERVICE" �> "OK" with button "6". Under poor reception condi-
tions it is possible with the 3 or 4 button to force the automatic chroma
standard switching function into the chroma standard on a per-1.3 Cancelling the Parental Lock
To cancel the parental lock enter the number 7038.
programme basis.
4.5 Switching off the Blue Screen Background2. Special Functions in the Dialog Center
Call up the dialog line "Blue Screen" via "DIALOG CENTER" �>
2.1 Activating or Deactivating the Economy Mains Switch (option)"OK" �> "SERVICE" �> "OK" �> with button "6". When this function is
Reach the "Economy mains switch" menu with button "6" via "DIALOGset to "off" the blue background is switched off (e.g. when the aerial
CENTER" �> "OK" �> "SPECIAL FUNCTIONS" �> "OK". With thesignal is missing).
4.6 Black Screen when Changing the Programme3 or 4 button select "1h�3h".
The TV receiver switches off completely from Standby mode at the
Call up the dialog line "Black Screen" via "DIALOG CENTER" �>predetermined time or by pressing the mains button 8 twice.
"OK" �> "SERVICE" �> "OK" with button "6". When this function is setThis function is not used when "off" is selected.
to "on" the screen is blanked when changing the programme.
2.2 Switching on with Programme "1" or "AV"
4.7 IDP2 (Dealer Programmer)Reach "TV on with" menu with button "6" via "DIALOG CENTER" �>
Call up the dialog line "IDP2 HP" via "DIALOG CENTER" �> "OK"
�> "SERVICE" �> "OK" with button "6". The characters change to red."OK" �> "SPECIAL FUNCTIONS" �> "OK". In "AV1" position the TV
The channels to be received can be programmed with the IDP2starts showing the AV picture.
2.3 Picture/Sound Options On or Off for all Programmes Programmer.
Reach the "Pict./sound opt." menu via "DIALOG CENTER" �>
4.8 Display of the Station Name On or Off"OK" �> "SPECIAL FUNCTIONS" �> "OK" by pressing button "6".
The station ident is read out from the VT (teletext) or the VPS signal (isWhen selecting "off" the scales indicating the analog values do not
not transmitted from all stations).appear.
Call up the dialog line "Station name" via "DIALOG CENTER"
2.4 Automatic Volume Limiter (option)�> "OK" �> "SERVICE" �> "OK" with button "6". With this function set
Reach the "Volume Limiter" dialog via "DIALOG CENTER" �> "OK"to "off" it is possible to avoid the station name being displayed on the
�> "SPECIAL FUNCTIONS" �> "OK" by pressing button "6". Thescreen for a short time when changing the programme.
volume of stations with large deviation is adjusted to normal deviation
when selecting "on".
2.5 Decoder Settings for Individual Programme Positions
By pressing button "6" call up the "Decoder Pxx" dialog via "DIALOG
CENTER" �> "OK" �> "SPECIAL FUNCTIONS" �> "OK". With the
3 or 4 button it is possible to set the decoder bit on a per-programme
basis.
See point 4.3 for setting and resetting all programme positions.
GRUNDIG Service1 - 17 |
ACEC
