DTR-8.2
PANEL VIEWS
IR IN/OUT
REAR PANEL 3If the DTR-8.2 is located inside a rack or cabinet that will not allow
infrared beams to reach the IR sensor, you will need to connect a
remote sensor to IR IN input to be able to use the remote controller.
(RI)
Then install the remote sensor in an unblocked location where you
The terminal on the DTR-8.2 is for connecting other Integra/
can easily point the remote controller.
Onkyo components equipped with the same terminal. When aUsing a mini-jack connector, connect the IR emitter to the IR OUT
component is -connected, you can point the remote controllerterminal on the DTR-8.2 and then place the IR emitter on the remote
supplied with the DTR-8.2 at the sensor on the DTR-8.2 and operatesensor of the component or facing it.
that component without having to switch remote controllers.
In addition, by connecting components to the terminal, you can
RS 232
also perform the system operations given below.
The RS 232 port is to be used in conjunction with an external
Power on/ready function
controller to control the operation of the DTR-8.2 by using an
When the DTR-8.2 is in the standby state, if an -connected
external device. The RS 232 port may also be used in the future to
component is turned on, then the DTR-8.2 also turns on and the input
update the operating software of the DTR-8.2 so that it will be able to
source selected at the DTR-8.2 automatically switches to that
support new digital audio formats and the like as they are introduced.
component.
If the power cord for an -connected component is connected to
the AC OUTLET on the DTR-8.2, or if the DTR-8.2 is turned on,
VIDEO IN/OUT
this function will not work.
These are the video inputs and outputs. On the rear panel, there are
Direct change functionfive video inputs and two video outputs and each one includes both
When the play button is pressed at an -connected component, thecomposite video and S video configurations. Connect VCRs, LD
input source selected at the DTR-8.2 automatically changes to thatplayers, DVD players, and other video components to the video
component.inputs.
Power off functionThe two video output channels can be used to be connected to video
When the DTR-8.2 is placed in the standby state, all tape recorders for making recordings.-connected
components are also automatically put into the standby state. When connecting a VCR or other video component, make sure
you connect the audio and video leads together (i.e., both to
CAUTION
VIDEO 3).
If an MD recorder is connected to the TAPE jack on the DTR-8.2,
switch the Input Selector from TAPE to MD.
MULTI CHANNEL INPUT
By connecting a DVD player, MPEG decoder, or other component
that has a multi channel port, you can playback the audio with 5.1
DTR-8.2
channel or 7.1 channel output. So, be sure to prepare a cable that can
REMOTECONTROL
properly connect the DTR-8.2 to the peripheral device.
connectorL (white)
Front output
Ex: Integra/Onkyo CDDIGITALR (red)OUTPUTPRE OUTRL
OPTFRONT
player1Subwoofer
SUBCENTER
2
connector
L (white)COAXSURR
1
Surround SURR BACK/
Ex: Integra/Onkyo cassette2 ZONE 2
C
tape deck
R (red)FRONT
3MULTI INPUT
OPTSUBCENTER
Ex: DVD-Audio player/MPEG1
decoderSURR
To connect components using the terminal, simply connect a2
SURRBACK
remote control cable from this terminal to the terminal of the3
RL
other component. An remote control cable with a 1/8-inch (3.5-R (red)
4
mm) miniature two-conductor plug comes with every cassette tapeSurround backGND
DIGITAL
deck, compact disc player, MD recorder, and DVD player that has anINPUT
terminal.L (white)
Center
When performing operations with -connected components
using the system, do not use the remote zone (Zone 2).
For remote control operation, the audio connection cables must
GND
also be connected.
Use this GND terminal for connecting the ground (or earth) wire if a
If a component has two terminals, you can use either one to
turntable is connected.
connect to the DTR-8.2. The other one can be used to daisy chain
with another component. |
ACEC
