AV-4300
AV-5000
2.13.1 Raster Position Adjustment
Adjustment preparation
1. Position adjustment
This will move an entire color. Use this adjustment to match
colors at the center of the screen.
2. Use the buttons below to switch color to adjust.
[1111] button : Green
[ 0 ] button : Red
[2222] button : Blue
Adjustment Procedure
1. Press the [LST-CH] button. Extra horizontal lines appear to
confirm raster position mode.
2. Use the cursor buttons to adjust position.
3. Press the [LST-CH] button again to exit raster position
mode.
NOTES :
1. Other functions cannot be accessed when in raster position
mode. Press the [LST-CH] button and confirm extra
horizontal lines disappear to exit raster position mode.
2. Press the [MENU] button to switch between all colors
displayed or adjustment color and Green only.
2.13.2 Convergence Point Adjustment
Adjustment preparation
1. Select color to adjust.
[1111] button : Green
[ 0 ] button : Red
[2222] button : Blue
2. Use [4], [6], [2] and [5] buttons to move the cursor position
(dotted lines).
3. Use cursor buttons to move the convergence.
4. Adjustment points are 117 points (H:13 x V:9 points). Refer
to section 2.13.
5. Start adjustment at the center of the screen.
6. Continue adjustment at next closest position.< DIGITAL CONVERGENCE REMOTE CONTROL BUTTON >
7. Adjust center area first, and ending with edge section.
Adjustment Procedure
NOTES :
1. Start adjustment at the center of the screen.1. CH I/II button : cross-hatch/video mode
2. Continue adjustment at next closest position.
3. Adjust center area first, and ending with edge sections.* Press [CH I/II] button 5 times to display external signal.
4. Calculation* Press [CH I/II] button 5 times again to return to DCU
internal cross-hatch.
When convergence adjustment is finished, press the2. MENU button : remove color mode
[CH(digit)] button on the remote control, then the calculation
mode starts. The operation time is about for 5 seconds andPress the [MENU] button to switch between all colors
no picture appears during this operation. This operation fillsdisplayed or adjustment color and green only.
convergence data between each adjustment points. If you* Press [0] button, then press [MENU] button : Red and
Green displayed (Blue removed)
find misconvergence more than 1mm, adjust the
convergence again.* Press [2] button, then press [MENU] button : Blue and
5. Write data to ROM. Press the [INDEX] button on remoteGreen displayed (Red removed)
control. First, press: "ROM W RITE?" is displayed for alarm.* Press [1] button, then press [MENU] button : only Green
Second, press Data starts to write to ROM, it takes aboutdisplayed
for 10 seconds and no picture appears during this operation.3. LST-CH button : raster position adjustment
When Green dot pattern appears, writing operation is OK. If4. 1 / 0 / 2 buttons : adjustment point mode
writing operation is OK, press any button, to return to the* Press [1] button 5 times to 9 (H:3 x V:3) points mode.
adjustment mode. When red dot appears, writing operation
* Press [0] button 5 times to 35 (H:7 x V:5) points mode.
is NG. If writing operation is NG, replace digital* Press [2] button 5 times to 117(H:13 x V:9) points mode.
convergence unit and readjust. Push the "SERVICE ONLY"
switch again to finish the adjustment.
6. The digital convergence has 2 modes 60Hz (NTSC) and
50Hz (PAL), change another mode then adjust again
(2.13.1 ~ 2.13.2).
30No. 51876 |
ACEC
