GB 385.DVDR1000 /0x1 /691 Diagnostic Software and Faultfinding Trees
5.2.2 Structure of the Player Script?Interactive tests: this part of the player test depends
strongly on user interaction and input to determine
The player script consists of a set of nuclei testing thenucleus results and to progress through the full test.
hardware modules in the DVD recorder: the Display PWB,Reading the error log information can be useful to
the Digital PWB, the Analogue In/Out PWB and the DVDRdetermine any errors that occurred recently during
module.normal operation of the DVD player.
Nuclei run by the player test need some user interaction; in?The loop test will perform the same nuclei as the dealer
the next table this interaction is described. The player test istest, but it will loop through the list of nuclei indefinitely.
done in two phases:
STEPDESCRIPTIONNUCLEUS
1Press OPEN/CLOSE and STOP at the same time and POWER ON the recorder to start the2
playerscript
2The local display shows FPSEGMENTS. Press PLAY to start the test.502
First the starburst pattern is lit, then the horizontal segments are lit, followed by the vertical
segments and the last test is light all segments test. After each of the 4 tests the user has to
confirm that the correct pattern was lit.
Press PLAY to confirm that the correct pattern was lit (four times if the FPSEGMENTS test
was successful).
Press RECORD to indicate that the correct pattern was not successfully lit.
Press STOP to skip this nucleus.
3The local display shows FPLABELS. Press PLAY to start the test.503
Press PLAY to confirm that all labels are lit.
Press RECORD to indicate that not all labels are lit.
Press STOP to skip this nucleus.
4The local display shows FPLIGHT ALL. Press PLAY to start the test.520
Press PLAY to confirm that everything was lit.
Press RECORD to indicate that not all patterns are lit.
Press STOP to skip this nucleus.
5The local display shows FPLED. Press PLAY to start the test.504
Press PLAY to confirm that the led is lit.
Press RECORD to indicate that the led is not lit.
Press STOP to skip this nucleus.
6The local display shows FPFLAP OPEN. Press PLAY to start the test.522
Press PLAY to confirm that the flap has opened.
Press RECORD to indicate that the flap did not open.
Press STOP to skip this nucleus.
7The local display shows FPKEYBOARD. Press PLAY to start the test.505
Attention all keys have to be pressed to get a positive result!
Press PLAY for more than one second to confirm that all the keys were pressed and shown
on the local display. If not all the keys were pressed, a FAIL message will appear on the
local display.
Press RECORD for more than one second to indicate that not all keys were pressed and
shown on the local display.
Press STOP for more than one second to skip this nucleus.
8The local display shows FPREMOTE CONTROL. Press PLAY to start the test.506
Press PLAY to confirm that a key on the remote control was pressed and shown on the
local display. Only one key has to be pressed to get a successful result.
Press RECORD to indicate that the key on the remote control was pressed but not shown
on the local display.
Press STOP to skip this nucleus.
9The local display shows FPDIMMER. Press PLAY to start the test.518
Press PLAY to confirm that the text on the local display was dimmed.
Press RECORD to indicate that the text on the local display was not dimmed.
Press STOP to skip this nucleus.
10The local display shows FPBEEPER. Press PLAY to start the test.514
Press PLAY to confirm that the beeper on the front panel sounded.
Press RECORD to indicate that the beeper on the front panel did not sound.
Press STOP to skip this nucleus.
11The local display shows FPFLAP CLOSE. Press PLAY to start the test.523
Press STOP to skip this nucleus.
12The local display shows ROUTE VIDEO. Press PLAY to start the test.712
Press STOP to skip this nucleus.
13The local display shows ROUTE AUDIO. Press PLAY to start the test.713
Press STOP to skip this nucleus.
14The local display shows COLOUR-BAR ON. Press PLAY to start the test.120
Press STOP to skip this nucleus.
15The local display shows PINK NOISE ON. Press PLAY to start the test.115
Press STOP to skip this nucleus.
16The local display shows PINK NOISE OFF. Press PLAY to start the test.116
Press STOP to skip this nucleus.
17The local display shows SINE ON. Press PLAY to start the test.117
Press STOP to stop the sine.
Press STOP to skip this nucleus.
18The local display shows COLOUR-BAR OFF. Press PLAY to start the test.121
Press STOP to skip this nucleus.
19The local display shows BERESET. Press PLAY to start the test.603
Press STOP to skip this nucleus.
20The local display shows BETRAY OPEN. Press PLAY to start the test.616
Press STOP to skip this nucleus.
21The local display shows BETRAY CLOSE. Press PLAY to start the test.615
Press STOP to skip this nucleus.
22The local display shows BEWRITE READ. Press PLAY to start the test.617
Press STOP to skip this nucleus.
23The local display shows BETRAY OPEN. Press PLAY to start the test.616
Press STOP to skip this nucleus.
24The local display shows BETRAY CLOSE. Press PLAY to start the test.615
Press STOP to skip this nucleus.
25The local display shows READ ERRORLOG. Press PLAY to start the test.633
Press STOP to skip this nucleus.
If the player test succeeded, the user/dealer script will start in an endless loop.
If the player test failed, the local display will display FAIL and the error code
CL 16532095_063.pdf
140801 |
ACEC
