Restoring the color from the EASY or sRGB menus
Adjusting the quality of the picture Adjusting the convergence (CONV)Additional settings (OPTION)
(IMAGE RESTORATION function)
The colors of most display monitors tend to gradually lose brilliance (SCREEN)The CONV settings allow you to adjust the quality of the picture You can manually degauss (demagnetize) the monitor, change the
over several years of service. The IMAGE RESTORATION feature by controlling the convergence. The convergence refers to the menu position, and lock the controls.
found in the EASY and sRGB menus allows you to restore the color The SCREEN settings allow you to adjust the quality of the alignment of the red, green, and blue color signals.
to the original factory quality levels.picture by controlling the moire and landing.If you see red or blue shadows around letters or lines, adjust the 1Press the joystick.
Y If the color is irregular at the corners of the screen, adjust the convergence.The main MENU appears on the screen.
1Move the joystick left or right to select EASY or landing.These settings are stored in memory for all input signals.
sRGB mode.Y If elliptical or wavy patterns appear on the screen, cancel the 2Move the joystick to highlight OPTION and press
moire.1Press the joystick.the joystick again.
2First move the joystick up or down to select The CANCEL MOIRE and MOIRE ADJUST settings are stored The main MENU appears on the screen.The OPTION menu appears on the screen.
(IMAGE RESTORATION). Then move the in memory for the current input signal. All other settings are
joystick to the right.stored in memory for all input signals.2Move the joystick to highlight CONV and press 3Move the joystick up or down to select the desired
The picture disappears while the color is being restored (about the joystick again.adjustment item.
2 seconds). After the color is restored, the picture reappears 1Press the joystick.The CONVERGENCE menu appears on the screen.Adjust the selected item according to the following
on the screen again.The main MENU appears on the screen.instructions.
3First move the joystick up or down to select the
Notes2Move the joystick to highlight SCREEN and desired adjustment item. Then move the joystick left
x Degaussing the screen
Y Before using this feature, the monitor must be in normal operation press the joystick again.or right to make the adjustment.
mode (green power indicator on) for at least 30 minutes. If the monitor The SCREEN menu appears on the screen.The monitor is automatically demagnetized (degaussed) when the
goes into power saving mode, you must return the monitor to normal power is turned on.
operation mode and wait for 30 minutes for the monitor to be ready. 3First move the joystick up or down to select the SelectToTo manually degauss the monitor, first move the
You may need to adjust your computerOs power saving settings to keep horizontally shift red or blue shadojoystick up or down to select ws (DEGAUSS). Then
the monitor in normal operation mode for the full 30 minutes. If the desired adjustment item. Then move the joystick left move the joystick to the right.
or right to make the adjustment.
monitor is not ready, the following message will appear. vertically shift red or blue shadoThe screen is degaussed for about 3 seconds. If a second degauss ws
cycle is needed, allow a minimum interval of 20 minutes for the
COLORSelectTo TOPvertically shift red or blue shadobest result.ws at
EASYEXPERTs RGB reduce any color irregularities in the V CONVER TOPthe top of the screenGB
1-65000K6500K9300 K5000KLANDINGscreenOs top left corner to a minimum. BOTvertically shift red or blue shadoxChanging the menws at uOs position
V CONVER the bottom of the screen
IMAGE reduce any color irregularities in the Change the menuOs position if it is blocking an image on the BOTTOM
RESTORATIONLANDINGscreenOs top right corner to a screen.
AVAILABLE
AFTER WARM UPminimum.To change the menuOs on-screen position, first move
the joystick up or down to select (OSD H POSITION)
reduce any color irregularities in the for horizontal adjustment, or (OSD V POSITION) for
Y The monitor may gradually lose its ability to perform this function due LANDINGscreenOs bottom left corner to a vertical adjustment. Then move the joystick left or right
to the natural aging of the picture tube.minimum.
to shift the on-screen menu.
reduce any color irregularities in the
LANDINGscreenOs bottom right corner to a x Locking the controls
minimum.
To protect adjustment data by locking the controls, first
turn the moire cancellation function move the joystick up or down to select (CONTROL
CANCEL MOIRE *ON or OFF.LOCK). Then move the joystick to the right, to select
(MOIRE ADJUST) appears in ON.
the menu when you select ON.Only the ! (power) switch, EXIT, and (CONTROL LOCK)
adjust the degree of moire of the OPTION menu will operate. If any other items are
MOIRE ADJUSTcancellation until the moire is at a selected, the mark appears on the screen.
minimum.
To cancel the control lock
* Moire is a type of natural interference which produces soft, wavy lines Repeat the procedure above and set (CONTROL LOCK) to OFF.
on your screen. It may appear due to interference between the pattern
of the picture on the screen and the phosphor pitch pattern of the
monitor.
Example of moire
Note
The picture may become fuzzy when CANCEL MOIRE is set to ON.
1415 |
ACEC
