1234
7.1.8 ID NUMBER AND ID DATA SETTING
Caution:
For the DVD players compatible with DVD-RW, for playback of a DVD-RW disc (CPRM), it is necessary that an individual ID
Anumber and ID data are set for each player. If the ID number and ID data be not properly set in the manner described below,
future operations cannot be guaranteed. The ID number is written on the yellow label at the rear panel of the player.
If there is no yellow label, before downloading FLASH ROM, take note of the ID number set following the procedures
outlined in "ID Number Confirmation Mode" on the next page.
Note: Enter ID numbers while the unit is in Stop mode so that the values set will be immediately written to the flash ROM.
Setting an ID number or ID data is required in the 5 After entering all 9 digits, if you press the SEARCH key, the
following case:unit unconditionally sets the input number as the ID number.
If "No ID Number!" or "NO ID DATA!" is displayed on the Then the unit automatically enters Player's Data Input Mode.
(The SEARCH key is not accepted after all 9 digits have been
TV screen and on the FL display for a few seconds
entered.)
immediately after the power to the player is turned on or
during Stop mode.
[Player's ID Number Setting]
B
ID Number ?
JIGS AND MEASURING INSTRUMENTS
0 0 0 0 0 0 0 0 1
4 <PLAY> Compare Mode
5 <SEARCH> Enter
Input ID Number !
Service Remote ControlDVD Data Disc
Unit (GGF1381)(GGV1171)
6 This display appears when the PLAY key is pressed in Step 4.
C
Enter a 9-digit number to compare. The number is also
ID Number Input Mode
displayed on the FL display.
1 To enter ID Number Input Mode, with no ID number set, such as
7 By pressing the CLEAR key without having input a number, the
in a case of immediately after upgrading the firmware, press the
unit returns to Step 2 without doing anything else. Each press
ESC key then the STEREO key.
of this key after a number has been input deletes one digit.
Note: If a previous ID number and ID data, such as a factory-
preset ID number and ID data, are maintained, the unit
[Player's ID Number Setting]
enters ID Number Confirmation Mode when the above keys
ID Number ?
are pressed. However, if only an ID number is maintained,
the unit enters ID Data Input Mode. 0 0 0 0 0 0 0 0 1
Compare
2 Enter a 9-digit ID number. The ID number is also displayed on
6
the FL display.
D
3 By pressing the CLEAR key without having input a number, you
can exit this mode. Each press of this key after a number has
been input deletes one digit.
Input ID Number !
[Player's ID Number Setting]
ID Number ?
8 After entering all 9 digits, if you press the PLAY key, the unit
2 - - - - - - - - -
compares the numbers input in Steps 2 and 6, and only if the
numbers match, that number is set as the ID. Then the unit
3 <CLEAR> Exitautomatically enters ID DATA Input Mode. If the numbers do not
match, the disc tray is opened, and the unit exits ID Number
Input Mode.
E Input ID Number !Note: If you press the PLAY button before inputting a 9-digit ID
number, the unit returns to Step 6 without doing anything
else.
[Player's ID Number Setting]
4 After entering all 9 digits, if you press the PLAY key, the unit ID Number ?
enters Compare mode. Enter the same ID number again. Only 0 0 0 0 0 0 0 0 1
if your two input numbers match, the ID number is set. Compare
Compare
mode helps eliminate mistyping of the ID number.
0 0 0 0 0 0 0 0 1
Note: If you press the PLAY button before inputting a 9-digit ID
number, the unit returns to Step 2 without doing anything
8 <PLAY> Enter
else.
Input ID Number !
F
58DV-270-S
1234
ACEC
