GM-X624, GM-X524
)2WW
W´
2 (EIAJ)
´
allowable)allowable)
310 (D) mmWW
´12-1/4 (D) in.]
´
for four channels)for two channels)
WW61 (H) 4 / 240 W (1 N 8
´´W
2-3/8 (H)
´, 20 N 20,000 Hz, 0.08% THD)
W, 20 N 20,000 Hz, 0.8% THD), 20 N 20,000 Hz, 0.8% THD)
WW
4 (at 14.4V, 4
´2 (at 14.4V, 4 4 (at 14.4V, 2
´´
. . . . . . . . . . . . . . . .120 W . . . . . . . . . . . . . . . . .60 W
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12.5 A (4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[10 (W) . . . . . . . . . . . . . . . . . . . . . . . . . . .(Bridge connection: 2 N 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cut off slope: �12 dB/oct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cut off slope: �12 dB/oct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Speaker: 1.6 N 10 V/78 k
modification without notice due to improvements.rent drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.
SPECIFICATIONSPower source . . . . . . . . . . . . . . . . . . . . . .14.4 V DC (10.8 N 15.1 Vallowable) Grounding system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Negative type Current consumption . . . . . . . . . . . . . . . . . .29 A (at continuous power, 4Average current drawn* . . . . . . . . . . . . . . . . . . . .8 A (4 Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 A Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 (W) Weight . . . . . . . . . . . . . . . . . .4.1 kg (9.0 lbs.) (Leads for wiring not included) Maximum power output . . . . . . . . . . . . . . . . . . .100 W Continuous power output 50 W Load impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Frequency response . . . . . . . . . . . . . . . . . . . . .10 N 50,000 Hz (+0 dB, �1 dB) Signal-to-noise ratio . . . . . . . . . . . . . . . . . . . . . . . . . .105 dB (IHF�A network) Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.004%(10W, 1 kHz) Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 dB (1 kHz) Low pass filter . . . . . . . . . . . . . . . . . . . . . . . . .Cut off frequency: 50 N 120 HzHigh pass filter . . . . . . . . . . . . . . . . . . . . . . . .Cut off frequency: 50 N 120 HzInput level / impedance . . . . . . . . . . . . . . . . . . . . . . . .RCA: 0.4 N 4.0 V/22 kNote:YSpecifications and the design are subject to possible*Average current drawnYThe average current drawn is nearly the maximum cur-
-
Amplifier with RCA input jacksCar stereo with RCA output jacks
RCA input
Connecting wires with RCA pin plugs(sold separately).
RCA input jack A, B
Special red battery wire [RD-223] (sold separately). After making all other connections at the amplifier, connect the battery wire terminal of the amplifier to the positive (+) terminal of the battery.Ground wire (black) [RD-223](sold separately). Connect to metal body or chassis.
Blue [RD-223] (sold separately). Connect the male terminal of this wire to the blue wire of the car stereo (SYSTEM REMOTE CON- TROL). The female terminal can be connected to the auto-antenna relay control terminal. If the car stereo does not have a system remote control ter- minal, connect the male terminal to the power ter- minal through the ignition switch.
External Output For details on how to connect to RCA input jacks A and B, see the OConnecting the Speakers and Input wires� section. If only one input plug is used, do not connect anything to RCA input jack B.
Connecting wires with RCA pin plugs(sold separately).
RCA output jack
Fuse (30 A)Fuse (30 A)
2
´
Speaker output terminal See the OConnecting the Speakers and Input wires� section for speak- er connection instruc- tions.
Grommet
Reverse
Fuse (20 A)
Connection Diagram
21 |
ACEC
