14B-S5
21B-S5
ŻŻŻŻŻŻŻŻŻŻŻŻŻ
SUB ADJ.ADJ.ADJ.SUB ADJ.
MODEMODEMODEMODE
Y-DELAYOFFSET
FORWARD : CH DOWN KEY REVERSE : CH UP KEYSUB TINT (SUB-TINT)
MAX VOLUME (SUB-VOL)SUB COLOUR (SUB-COL)
SUB CONTRAST (SUB-CON)SUB BRIGHTNESS (SUB-BRI)SUB SHARPNESS (SUB-SHP)OSD GRB REFERENCE (RGB)CATHODE DRIVE LEVEL (CDL)
MAX HOTEL VOLUME (HTL-VOL)HOTEL PROGRAM NO (HTL-PRG)BLACK LEVEL OFFSET R (CUT-R)BLACK LEVEL OFFSET G (CUT-G)
BLUE BACK CONTRAST (BB-CON)
ŻŻŻŻŻŻŻŻŻ
ADJ.ADJADJ.3-2
MODEMODEMODE
STEREO
WHITE POINTWHITE POINT
W.P. RED STD. W.T. (DRI-RS)W.P.BLUE STD. W.T. (DRI-BS)W.P. RED COOL W.T. (DRI-RC)
W.P. GREEN STD. W.T. (DRI-GS)W.P. BLUE COOL W.T. (DRI-BC)W.P. RED WARM W.T. (DRI-RW)W.P. BLUE WARM W.T. (DRI-BW)
W.P. GREEN COOL W.T. (DRI-GC)W.P. GREEN WARM W.T. (DRI-GW)
ICŻŻŻŻŻŻŻŻŻ
AGC &MODEMISC.MODEOPTION MODEAGC &MODEOPTION
GEOMETRICGEOMETRIC
SERVICE MODE VERTICAL SLOPE (V-LIN) VERTICAL AMP (V-AMP) VERTICAL SHIFT (V-CENT)HORIZONTAL BOW (HB) S-CORRECTION (S-COR)
AGC TAKE OVER POINT (AGC)FORWARD : CH DOWN KEY REVERSE : CH UP KEY * ( ) means OSD display.
�(1)In the Service Mode, Key is used to select the mode in the following order. HORIZONTAL SHIFT (H-CENT) HORIZONTAL PARALLELOGRAM (EW//) EAST-WEST PARABOLA/WIDTH (PARA)
2C bus control).
2C bus control and in the
2C bus control include preset-only
3-1
ADJUSTMENT PRECAUTIONS
Short JA122 & JA124 for 1 second and release to switch to the service mode position, and the microprocessor is in input mode. (Adjustment through the I(Use JWS Key to set as well).Press the CH DOWN / UP key on the remote controller to get ready to select the mode one by one.Press the CH DOWN / UP key on the remote controller to select the modes reversibly one by one.Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.Short JA122 & JA124 for 1 second and release to switch to the normal mode (OFF) position, and the microprocessor is in out of the service mode.Short JA122 & JA124 for 1 second and release to switch to the service mode position and turn on the main power switch. Initial values are automatically preset, only when a new EEPROM is used (Judge with the first 4 bytes).The initial data are preset as listed in pages 4, 5 & 6.Make sure the data need modify or not (Initial data).
FIRST TIME, make sure to short JA122 & JA124 to switch to the service mode position first and then turn on the main power switch. (See 2- 1 above).Precaution: If haven�t done this initiation, it may possibly generate excessive Beam current.
12345123(UA1 Series type RH-IX3412CE Attachment)
This model�s setting are adjusted in two different ways: though the Iconventional analog manner. The adjustments via the Iitems and variable data.1.Setting the service mode by the microprocessor.2.Factory Presetting.Note:Once the chassis has been assembly together and ready to be POWER ON for the3.For reference please check with memory map
3 |
ACEC
