14D1-SA/SF/GA/GF
14D2-SA/SF/GA/GF
t
Y: 0.275Y: 0.255
DRI-BW="DRI-BS"-7 DRI-GC="DRI-GS"-7 DRI-RC=25DRI-BW="DRI-BS"-7 DRI-GC="DRI-GS"-5 DRI-RC=27
KX: 0.272KX: 0.255LOWHIGH10cd/m2200cd/m2
°°°K DRI-GW="DRI-GS"-7°K DRI-GW="DRI-GS"-7
3.3Vdc0
1 2 3 4 1 2 3 4
same as beside procedure.trace line appear and make sure the colour appear whether red, green or blue.related test points as below which is based on colour appear at (2) RED = TP47R, GREEN = TP47G, BLUE = TP47B.tip of signal reach 3.3Vdc.Line 3 is one step (data) brighter than line 2
*Alternative Procedure (1) Step (1), (2), (3) and (4) are(2) Then continue adjust until re-(3) Connect the oscilloscope to(4) Then adjust Screen VR until the12# 12300#18000(MINOLTA COLOUR ANALYZER CA-100) *Note: Above Data can be UP/ DOWN by Volume key.14"* 12300* 18000
A.A.
mm
°8-2K Condition)
°K ( white ). * Note .
K And 18000
°
°K or 18000This adjustment must be done after warming up the unit for 30 minutes or longer with a beam current over 500
DRI-RW = 32 (FIXED), DRI-RS = 32 (FIXED) DRI-BC = "DRI-BS" (For 12300
that the line 1and 2 have the same darkness wherelse line 3 is one step (data) brighter than line 2. Finally data minus 1 to make line 1, 2, and 3 are in same level (darkness).
DRI-RS/RW/RC, DRI-GS/GW/GC, DRI-BS/BW/ BC, CUT-R and CUT-G must be INITIAL DATA.dark room.NO VIDEO signal.sistor.crease screen variable resistor until colour raster suddenly on and off (AKB start function).sistor until screen retrace line cut off. (Not Raster)Must confirm the AKB function in set before continue the next adjustment.hatch pattern with 4 black level windows)(-) TP603 (+).DRI-BS data to have a colour temperature of 12300and set BRIGHTNESS Y by generator, to **10 cd/m2 (MINOLTA CA-100) by reducing LUMINATE Y signal.temperature #. Then go back NORMAL mode (HIGH BRIGHT**) to check colour temperature. If out of range, back to (1).Note:
DATA, after finishing DRI-BS and DRI-GS DATA ADJUSTMENT.
Remark 1.Before CRT cutoff adjustment, SUB-BRIGHT,2. CRT Cutoff adjustment must be done inside a1.Switch TV to VIDEO mode,BLUE BACK OFF, with2.Press R/C to set Picture Normal condition. 3. First, off the screen by adjust screen variable re-*4. Next, checking AKB circuit function by slowly in-5. Then continue adjust until retrace line appear. 6. Finally, slowly decrease the screen variable re-Note :1.Call " SUB-BRI" in service mode. (Receive Cross-*(2) Adjust the " SUB BRIGHT " bus data in order1.Receive the "WHITE" pattern with BURST signal. 2.Press R/C to set Picture NORMAL condition. 3.Connect the DC miliammeter between TP6024.Check Beam current should be around 800 5.Set it to service mode and adjust the DRI-GS, &6.Receive "WHITE" pattern, WITH BURST signal,7.Adjust "CUT-R" & "CUT-G" to get desired colour* ADJUST DRI-GC/GW, DRI-BC/BW as following
2C BUS
2C BUS2C BUS
CRT CUTOFF ADJUSTMENT (ICONTROL)SUB-BRIGHT- NESS ADJUSMENT (ICONTROL)WHITE BAL- ANCE SERV- ICE MODE ADJ. (ICONTROL)
CRT CUT-OFF, SUB-BRIGHT AND WHITE BALANCE ADJUSTMENTNo.Adjusting pointAdjusting procedure/conditionsWaveform and others123
!
B G RR G BAbout 100Wedge "c"
Note***
CRT neck
RGBBGR
BGRFig. 5-1RGBFig. 5-2Fig. 5-3Fig. 5-4Wedge "a"6-pole magnet
Lacquer
4-pole magnet
B G RR G B!Lacquer
About 100Wedge "b"Purity magnet
8-1
Note*** SAMSUNG CRT: 32mm CPT CRT: 35mm TOSHIBA CRT: 35mm
the deflection coil upward.and swing the deflection coil downward.the deflection coil rightward.the deflection coil leftward.
gle in order to superpose the blue and red col- ours.gle in order to superpose the green colour over the blue and red colours.screen in the following steps. a)Fig. 5-1: Drive the wedge at point "a" and swingb)Fig. 5-2: Drive the wedge at points "b" and "c"c)Fig. 5-3: Drive the "c" wedge deeper and swingd)Fig. 5-4: Drive the "b" wedge deeper and swingtape over them.magnet unit (purity, 4-pole, 6-pole magnets) and magnet unit lock screw.Finally received the Red-only and Blue-only sig- nals to make sure there is no other colours on the screen.
CONVERGENCE ADJUSTMENT
1.Receive the "Crosshatch Pattern" signal. 2.Using the remote controller, call NORMAL mode.STATIC CONVERGENCE 1.Turn the 4-pole magnet to a proper opening an-2.Turn the 6-pole magnet to a proper opening an-DYNAMIC CONVERGENCE 1.Adjust the convergence on the fringes of the2.Fix all the wedges on the CRT and apply glass3.Apply lacquer to the deflection yoke lock screw,
CONVERGENCE ADJ. ( To be done after the purity adjustment)
1
No.Adjusting pointAdjusting procedure/conditionsWaveform and others
8 |