14PS1
?????????????
SUB ADJ.ADJ.ADJ.SUB ADJ.MODEMODEMODEMODE
Y-DELAYOFFSET
SUB TINT (SUB-TINT)
FORWARD : CH DOWN KEY REVERSE : CH UP KEYMAX VOLUME (SUB-VOL)SUB COLOUR (SUB-COL)
SUB CONTRAST (SUB-CON)SUB BRIGHTNESS (SUB-BRI)SUB SHARPNESS (SUB-SHP)OSD GRB REFERENCE (RGB)CATHODE DRIVE LEVEL(CDL)
MAX HOTEL VOLUME (HTL-VOL)HOTEL PROGRAM NO(HTL-PRG)BLUE BACK CONTRAST (BB-CON)BLACK LEVEL OFFSET R(CUT-R)BLACK LEVEL OFFSET G(CUT-G)
?????????
ADJ.ADJ.ADJ.3-2
MODEMODEMODE
STEREO
WHITE POINTWHITE POINT
W.P. RED STD. W.T. (DRI-RS)W.P.BLUE STD. W.P. (DRI-BS)W.P. RED COOL W.P.(DRI-RC)
W.P. GREEN STD. W.T.(DRI-GS)W.P. GREEN COOL W.P.(DRI-GC)W.P. BLUE COOL W.P. (DRI-BC)W.P. RED WARM W.P.(DRI-RW)W.P. BLUE WARM W.P.(DRI-BW)
W.P. GREEN WARM W.P.(DRI-GW)
IC?????????(EW//)
AGC &MODEMISC. OPTION MODEMODEAGC &MODE(PARA)
OPTION
GEOMETRICGEOMETRIC
HORIZONTAL BOW (HB)
VERTICAL SLOPE (V-LIN) VERTICAL AMP (V-AMP)S-CORRECTION (S-COR)
SERVICE MODE VERTICAL SHIFT (V-CENT)
AGC TAKE OVER POINT (AGC) HORIZONTAL SHIFT (H-CENT) HORIZONTAL PARALLELOGRAM EAST-WEST PARABOLA/WIDTHFORWARD : CH DOWN KEY REVERSE : CH UP KEY * ( ) means OSD display.
(1)In the Service Mode, Key is used to select the mode in the following order.
2C bus control and in the conventionalC bus control). (Use JWS Key to set as
2
3-1
2C bus control include preset-only items and variable data.
ADJUSTMENT PRECAUTIONS
microprocessor is in input mode. (Adjustment through the Iwell).microprocessor is in out of the service mode.main power switch.Initial values are automatically preset, only when a new EEPROM is used (Judge with the first 4 bytes ).
. Short JA 122 & JA 124 for 1 second and release to switch to the service mode position, and the. Press the CH DOWN / UP key on the remote controller to get ready to select the mode one by one.. Press the CH DOWN / UP key on the remote controller to select the modes reversibly one by one.. Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.. Short JA 122 & JA 124 for 1 second and release to switch to the normal mode (OFF) position, and the. Short JA 122 & JA 124 for 1 second and release to switch to the service mode position and turn on the. The initial data are preset as listed in page 5 & 6.. Make sure the data need modify or not (Initial data).
12345123make sure to short JA122 & JA124 to switch to the service mode position first and then turn on the main power switch (See 2-(1) above).Precaution: If haven't done this initiation, it may possibly generate excessive Beam current.
(UA1 Series type RH-IX3410CE Attachment)
This model's setting are adjusted in two different ways: through the Ianalog manner. The adjustments via the I1. Setting the service mode by the microprocessor.2.Factory Presetting.Note:Once the chassis has been assembly together and ready to be POWER ON for the FIRST TIME,3.For reference please check with memory map
3 |
ACEC
