21GF30
21GF50
?? ????? ? ?? ? ??
SUB ADJ.ADJ.ADJ.SUB ADJ.
MODEMODEMODEMODE
Y-DELAYOFFSET
FORWARD : CH DOWN KEY REVERSE : CH UP KEY * ( ) means OSD display. Max Volume (SUB-VOL) Sub Contrast (SUB-CON) Sub Colour (SUB-COL) Sub Brightness (SUB-BRI) Sub Tint (SUB-TINT)Sub Sharpness (SUB-SHP) Max Hotel Volume (HTL-VOL) Hotel Program number (HTL-PRG) Blue Back Contorast (BB-CON) OSD RGB Reference (RGB) Black Level off-set R (CUT-R) Black Level off-set G (CUT-G) Cathode Drive Level (CDL)
ollowing order.
IC? ? ? ? ? ? ? ? ? E-5
ADJ.ADJ.MODEOPTION MODEMODE
WHITE POINTWHITE POINT
White point Red Standard white temp.(DRI-RS) White point Green Standard white temp. (DRI-GS) White point Blue Standard white temp (DRI-BS) White point Red Cold white temp. (DRI-RC) White point Green Cold white temp. (DRI-GC) White point Blue Cold white temp. (DRI-BC) White point Red Warm white temp. (DRI-RW) White point Green Warm white temp. (DRI-GW) White point Blue Warm white temp. (DRI-BW)
?? ? ? ? ? ? ? ? ? ? ? ?
AGC &MODEMISC.MODEAGC &MODEOPTION
GEOMETRICGEOMETRIC
SERVICE MODE
AGC Take Over Point (AGC) Vertical Slope (V-LIN) Vertical Amplitude(V-AMP) Vertical Shift (V-CENT) Horizontal shift (H-CENT) East-West width (H-SIZE) Horizontal Parallelogram (EW//) East-west Parabola/Width (PARA) East-west Upper Corner Parabola (COR(U)) East-west Lower Corner Parabola (COR(L)) East-west Trapezium (TRAPE) Horizontal Bow (HB) S-Correction (S-COR)
(1) In the Service Mode, Key is used to select the mode in the fFORWARD : CH DOWN KEY REVERSE : CH UP KEY * ( ) means OSD display.
ytes).
y one.le.
ventional
wer switch.
st and then turn on
ariable data.versibly one by one.
n on the main po
ork to identify a spot in troub
2C bus control and in the con, the data can be modified.
UTIONS
w EEPROM is used (Judge with the first 4 b
2IC1003EEP ROM3IC801TVPROCESSOR4IC401AV SWITCH5IC305SOUND PROCESSOR6IC2300IGR(/NICAM) DECODER8TU201TUNERE-4 it may possibly generate excessive Beam current.
hment)
us control). (Use JWS Key to set as well).ve).
ly together and ready to be POWER ON for the FIRST TIME,
Flashing timePart's Ref.No.Remarks
2C bus control include preset-only items and v
o different ways: through the I
WN key on the remote controller
WN / UP key on the remote controller to get ready to select the mode one bWN / UP key on the remote controller to select the modes re
ADJUSTMENT PRECAt TP1001 & TP1002 to switch to the service mode position fir
upted by IIC bus line error, the following indicators w
vice mode by the microprocessor.
LED (RED) flashing:
mode. (Adjustment through the I2C bin out of the service mode.Initial values are automatically preset, only when a ne
. Short TP1001 & TP1002 to switch to the service mode position, and the microprocessor is in input. Press the CH DO. Press the CH DO. Using the VOLUME UP/ DO. Disconnect TP1001 & TP1002 to switch to the normal mode (OFF) position, and the microprocessor is. Short TP1001 & TP1002 to switch to the service mode position and tur. The initial data are preset as listed in page E-9, E-10 & E-11.. Make sure the data need modify or not (Initial data).
12345123make sure to shorthe main power switch (See 2-(1) aboPrecaution: If havenOt done this initiation,If the set is interr
(UAF Series type RH-iX3417CE Attac
This modelOs setting are adjusted in twanalog manner. The adjustments via the I1. Setting the ser2.Factory Presetting.Note:Once the chassis has been assemb3.For reference please check with memory map4.Trouble indications
3 |