29H-FD1F
29H-FG1F
aveform or remarksaveform or remarks
WW
BBE and Super Bass in the sound menu.out BBE and with Bass + in the sound menu.
Ref : Apx.13.3V.#1 : Sound setting for model with#2 : Sound setting for model with-
1 Vrms.
1 Vrms.?
?
17-2
OFFOFFOFF
Adjustment conditions/procedureAdjustment conditions/procedure
Setting item#1#2 EqualizerMusicMusic SurroundOFFOFF BBEOFF- Balance00 AVLSuper BassOFF- Bass +-ONEqualizerMusic SurroundOFF BBEOFF Balance0 AVLSuper BassON
SOUND OUTPUT CHECKING
of D604.that the protector does not operate.that the protector operate.sound setting as follow.Connect the voltmeter to the speaker terminal and make sure the reading is 9 dummy load.sound setting as follow.make sure the reading is 15
1.Receive E-5ch(Monoscopepattern). 2.Connect the bias box to the cathode side (R607)3.Set the voltage of the bias box at 10V, and verify4.Set the voltage of the bias box at 18V, and verify1.Receive the E-10ch (PAL colour bar). 2.Set the volume to maximum and set the other3.1.Receive the E-10ch (PAL colour bar). 2.Connect the woofer wire from P303 to a 16 ohm3.Set the volume to maximum and set the other4.Connect the voltmeter to the dummy load and
PROTECTOR OPERATION CHECKING
Adjustment pointH, V PROTEC- TORAdjustment pointFront speaker output check- ingRear woofer ouput check- ing (For model with woofer box only)
112
No.No.
AND AUDIO)
aveform and others
W
17-1
50kHz Dev).
?
(Continued)
TION CHECKING (VIDEO
Adjusting procedure/conditions
the COLOUR SYSTEM key to select modes ex- cept PAL, check the COLOUR is not working prop- erly. Then, select the "PAL" mode. Check again its colour so that it is working properly.COLOUR SYSTEM key to select modes except SECAM, check the COLOUR is not working prop- erly. Then, select the "SECAM" mode. Check again its colour so that it is working properly.Receive ?NTSC 4.43? signal, press COLOUR SYSTEM key to select modes except NTSC4.43, check the COLOUR is not working properly. Then, select the ?NTSC 4.43? mode. Check again its colour so that it is working properly.thru AV, press COLOUR SYSTEM key to select modes except N4.43/3.58, check the COLOUR is not working properly. Then, select the ?NTSC 4.43/3.58? mode. Check again its colour so that it is working properly.Receive ?PAL-D/K? signal, press the ?SOUND SYSTEM? to select B/G, I. Check the sound out- put is not working properly. Select D/K and check the sound output to make sure it is working prop- erly.TEM? to select B/G, D/K. Check the sound output is not working properly. Select I and check the sound output to make sure it is working properly.Receive ?PAL-B/G? signal, press the ?SOUND SYSTEM? to select I, D/K. Check the sound out- put is not working properly. Select B/G and check the sound output to make sure it is working prop- erly.Receive PAL COLOUR BAR with SOUND 400Hz, 100% MODULATION (Maximum volume, and check the headphone output with 400Hz sound and no sound out from speaker.Ref : OUTPUT level of HEADPHONE is as following. Apx. 500mVp-psure the sound is heard from the speakers. Then put the unit in no signal state.
1.Receive the "PAL COLOUR BAR" signal, press2.Receive "SECAM COLOUR BAR" signal, press3.4.Receive ?NTSC 4.43/3.58 COLOUR BAR? signal1.2.Receive ?PAL-I? signal, press the ?SOUND SYS-3.1.2.1.Receive "PAL COLOUR BAR" signal. 2.Turn up the volume control to maximum, make3.Check the sound mute is effective. 4.Finally turn sound level of CTV to minimum.
COLOUR SYSTEMSOUND SYSTEMHEADPHONE OUTPUT CHECKINGNOISE MUTE CHECKING
FUNCTION OPERANo.Adjusting point910 11 12
17 |
ACEC
