29H-FG5A
Dark whiteDark white
ADJUSTMENTaveform or remarks
W
50% white50% white
Use the window pattern of the sig- nal generator SX-1006 for adjust- ment.Use "Y" of Minolta color analyzer CA-100 in adjustment.Use the window pattern of the sig- nal.
Note 1:Note 1:Note 2:generator SX-1006 for adjustment.
.
-RW/
-IN SIG-mode to
Vmode to
-RS-DVD, 0.5cd.
input.? input.AVAV
AVAV
, and adjust 50%
, and adjust 50% white, and adjust 50% white14-2
-RS-DVD-GS-DVD
0.5cd of the window pat-
AND SUB-CONTRAST ?
TV set already in the RF re-TV set already in the RF re-
-GW/C-DVD setting data are as, and adjust the right dark white
10cd.
?
10cd. 10cd.
??
Adjustment conditions/procedure
(DRI-GS-DVD, DRI-BS-DVD, CUT
component signal).(AV-IN SIGNAL) and subsequence above. CUT-GS-DVD)with the remote controller to 165 NAL).DVD can be obtain by using same calculation as white balance adjustment above (No.2). CUT C-DVD and CUT follow.CUT-RW/C-DVD = CUT CUT-GW/C-DVD = CUTler.remote controller area of the window pattern to 3.0 cd ( Component signal) ( Window Pattern)ler.Select the SUB-BRIGHT adjustment mode (DVD) , and adjust the right dark white area of the win- dow pattern to 3.0 cd tern.ler.with the remote controller to 130 ceiving atate before changing to contimue with this adjustment (no power OFF from the previous adjustment). ( Component signal) (Window Pattern)(DVD) with the remote controllerwhite to 130 ceiving atate before changing to contimue with this adjustment (no power OFF from the previous adjustment).
1.The window pattern is received with DVD signal (2.Apply the adjustment in the same manners as 23.Select the SUB-CONTRAST adjustment modeApply the adjustment after the end of 2 (ANote: 1. All of the DRI-GW/C-DVD & DRI-BW/C-1.Receive the window pattern with 2.Make the image normal with the remote control-3.Select the sub- bright adjustment mode with the1.Select DVD mode. 2.Receive the signal of the DVD signal generator .3.Make the image normal with the remote control-4.1.Receive the window pattern with 2.Make the image normal with the remote control-3.Select the SUB-CONTRAST adjustment mode Note : Make sure the 1.Select the DVD mode. 2.Receive the signal of the DVD signal generator3.Select the SUB-CONTRAST adjustment modeNote : Make sure the
2C BUS2C BUS2C BUSC BUSC BUS
2I2I
CUT-OFF, BACKGROUND Adjustment pointWHITE BAL- ANCE BACK- GROUND I ADJUSTMENT (DVD SIGNAL)SUB-BRIGHT- NESS ADJUSMENT (I CONTROL) (AV-IN SIGNAL)SUB-BRIGHT- NESS ADJUSMENT (ICONTROL) (DVD SIGNAL)SUB-CON- TRASTADJUSMENT (AV-IN SIG- NAL)SUB-CON- TRASTADJUSMENT (DVD SIGNAL)
34567
No.
: 0.310: 0.255: 0.261
Y Y Y Y : 0.275
ADJUSTMENTaveform or remarks
W
CA-100)DRI-GW = "DRI-GS" - 7 DRI-BW = "DRI-BS" - 7 DRI-GC = "DRI-GS" - 7 DRI-RC = 25DRI-GW = "DRI-GS" - 7 DRI-BW = "DRI-BS" - 7 DRI-GC = "DRI-GS" - 5 DRI-RC = 27DRI-GW = "DRI-GS" - 5 DRI-BW = "DRI-BS" - 5 DRI-GC = "DRI-GS" - 7 DRI-RC = 25
7500K X : 0.300 18000K X : 0.255 17000K X : 0.261 12300K X : 0.272( With Monolta color thermometer* 12300_K* 17000_K & 18000_K* 7500_K
,.
A.
?
A115
50-RW/C
?
f , with no
able 2-1 at
input.TA, after finish-
T
..AV adjustment.
TA
DATA.
ABLE" and "IN".14-1
, DRI-BC/BW , CUT
AND SUB-CONTRAST
Adjustment conditions/proceduremore with the beam current 1700 (On the white or green monocolor screen)ment destination as shown in page 6.Adjust DRI-GC/GWand CUT-GW/C as following DAing DRI-BS and DRI-GS DA
2:The colour temperature is based on the ship-3: CUT-RW/C = CUT-RS CUT-GW/C = CUT-GS DRI-RW = 32 (FIXED), DRI-RS = 32 (FIXED) DRI-BC = "DRI-BS" (For 7500_K, 12300_K, 17000_K and 18000_K Condition)
lowing items are in INITIALa) A063 CUT-RS = 32 b) A064 CUT-GS = 32 c) A114 CUT OFF = 6video signal and Press R/C to set picture into normal condition.Go to service mode at adjustment mode item (VG2).the following OSD will appear at bottom of screen. UNSTABLE OUT ABOVEsistor until following OSD appearSTABLE IN ABOVE / BELOW *voltage value. If it show "BELOW", please in- crease the screen voltage and vice versa until "STABLE" AND "IN" OSD appearindicate "ABOVE" or "BELOW", the important thing is OSD change to "STMake the picture normal with the remote controllerR623.Coarsely confirm the beam current to approx. 1.7mA.color temperature of the 50% white.Adjust the right dark area of the window to 12300K with CUT-RS and CUT-GS.Go back to 50% white area to check colour tem- perature, if out of range, please go back to step (6).
Note : 1. Before CRT cutoff adjustment, make sure fol-1.Switch TV to video mode , blue back of2.3.Adjust screen voltage until retrace line appear4.Finally , slowly decrease the screen variable re-* The last OSD row is the indication of the screenNote :No matter the indication of last row's OSD is1.Receive the internal RF monoscope pattern. 2.3.Connect the beam ammeter between terminal of4.5.Receive the window pattern with 6.With the data of DRI-GS and DRI-BS, adjust the7.8.Note 1: Apply this adjustment after aging 30 min or
2C BUS2C BUS
CRT CUTOFF ADJUSTMENT (ICONTROL)WHITE BAL- ANCE BACK- GROUND IADJUSTMENT (AV-IN SIGNAL)
CUT-OFF, BACKGROUND Adjustment point
12
No.
14 |
ACEC
