60FW-53E
70FW-53E
81FW-53E
9- 9- 9- 9- 9- S-CORRECTION
a) Internal pattern signal will be displayed.
b) When volume-up button is pressed, upper and lower scanning decreases, and
center scanning increases.
c) When volume-down button is pressed, upper and lower scanning increases,
and center scanning decreases.
d) Adjust the S-CORRECTION to obtain a balance between upper, lower and
Fig. 10
center (fig. 10).
10- 10- 10- 10- 10- VERTICAL SHIFT
a) Internal pattern signal will be displayed.
b) When volume-up button is pressed, picture moves up.
c) When volume-down button is pressed, picture moves down.
d) Adjust the horizontal location to obtain picture centering (fig. 11).
Fig. 11
CONTRAST ADJUSTMENT
COLOUR ADJUSTMENT
The following adjustments are only required when Picture Tube,Up/Down volume buttons are used to adjust the
IC801 or IC1801 are changed:contrast of the following items:
-TELETEXT MIX MODE CONTRAST.
1. RED CUT OFF / GREEN CUT OFF / BLUE CUT OFF-TELETEXT CONTRAST.
1.1 Adjust G2.-OSD CONTRAST.
1.2 Tune a white card.
DVCO ADJUSTMENT (PAL)
1.3 Adjust colour to minimum.
a) Receive Philips pattern signal.
1.4 Position colourimeter in the center of screen.
b) When Stand-by button is pressed (Remote Control
1.5 Adjust brightness and contrast to obtain a luminance of
Unit), start
?20 NITS.
1.6 Operate in Service Mode and select location RED CUT
DVCO ADJUSTMENT (NTSC)
OFF / GREEN CUT OFF / BLUE CUT OFF, to obtain colour
Adjust not required.
coordinates:
X=0.290 ? 0.015 Y=0.300 ? 0.015
AUTO INSTALLATION OFF/ON
When ON is selected, the TV will perform the
To increase press volume-up button and to decrease press
autoinstallation sequence as soon as service mode is
volume down button.
removed.
RED CUT OFF alter ?X? coordinate.
GREEN CUT OFF alter ?Y? coordinate.
BLUE CUT OFF alter ?X? and ?Y? coordinate.PROTECTIONS CANCEL
a) Connect Test Pattern signal to antenna terminal.
2. RED GAIN / GREEN GAIN / BLUE BAIN
b) Press main switch to OFF.
2.1 Using brightness and contrast buttons, select a
c) Press volume-down and channel-up buttons and
luminance of ?120 NITS.
main switch to ON simultaneously.
2.2 Operate in Service Mode and select location RED GAIN
d)?Service Software Vxx.xx? appears o screen.
/ GREEN GAIN / BLUE GAIN, to obtain colour coordinates:
e)Press main switch to OFF.
X=0.290 ? 0.015 Y=0.300 ? 0.015
To increase press volume-up button and to decrease pressAGC ADJUSTMENT
volume down button.
a) Tune the TV into CH10 (pattern generator).
RED CUT OFF alter ?X? coordinate.
b) Adjust the signal strength to 57dB mV
GREEN CUT OFF alter ?Y? coordinate.
c) Press the stand-by button on the Remote Control
BLUE CUT OFF alter ?X? and ?Y? coordinate.
(red button).
The TV will perform automatically the AGC.
2.3 Exit Service Mode and check colour coordinates ?X?
and ?Y? at 20 and 120 NITS. It may be necessary to repeat
AFT ADJUSTMENT PAL BG, SECAM L
procedure 1 and 2 of COLOUR ADJUSTMENT.
a) Tune the TV into CH69 (pattern generator).
b) Press the stand-by button on the Remote Control
ACCESS TO NVM
(red button).
Press CH U to move in the following sequence:
The TV will perform automatically the AFT.
ALTER NVM PAGŢ ALTER NVM POS Ţ ALTER VNM
AFT ADJUSTMENT SECAM L?
VAL to alter presseting adjustments, press up/down-
a) Tune the TV into CH04 (pattern generator).
volume buttons on ALTER NVM VAL.
b) Press the stand-by button on the Remote Control
!CAUTION: Do not change NVM VALUE to avoid(red button).
risk of serious damages to TV set.The TV will perform automatically the AFT.
6 |
ACEC
