SHARP AL1010 Repair Manual

$7.99

SHARP AL1010 - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

The manual also covers models

AL1000

Product Reviews

There are currently no reviews for this product.

Other reviews

Jim Carrier - 08/02/2006

Outstanding and fast service! I received service manual in a moment after order. Thanks to this manual I can use my printer again!

Fabian Castle - 08/01/2006

Thanks for the excellent service. The manual arrived quickly and in excellent condition. Quality A+++!

Patrick Guice - 04/23/2008

Phenomal manual great resoulution and very legible. Will become very helpfull in future for parts and service.

Krzysztof Mazurek - 11/27/2007

Super ! Szukałem wszędzie i tutaj po 10 minutach miałem schemat w swoim PC.

Aaron Lawrence - 01/02/2008

Contains mechanism diagrams, parts lists and schematics for all worldwide versions of DC-X88Z. Also includes remote schematic etc. A few non-essential pages are missing such as specifications. Includes the mechanical and electronic calibration instructions for the tape decks.

Customers who bought this product also purchased

SHARP 10P35G Service Manual	SHARP 14BN1 Service Manual	SHARP 14BN1A Service Manual
SHARP 20PL83 Service Manual	SHARP 10P18G Service Manual	SHARP 10P28G Service Manual

Click to see text excerpt from the manual

AL-1000/1010
Main codeMain codeContents
2620Rear edge void setting
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of rear edge void setting is displayed.
2. Enter the code number of rear edge void setting and press the START key, and the setting will be changed.
Code numberRear edge void setting
0Rear edge void allowed
1Rear edge void not allowed
30CE mark application control ON/OFF setting
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of CE mark application is displayed.
2. Enter the code number of CE mark application and press the START key, and the setting will be changed.
Code numberCE mark application setting
0CE mark application control OFF
1CE mark application control ON
38Drum life over stop cancel
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
Code numberSetting
0Stop at drum life over
1Stop cancel at drum life over
39Memory capacity setting
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
Code numberSetting
0No memory
14Mbyte
26Mbyte
40Polygon motor OFF time setting
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
Code numberSetting
00 sec
130 sec
260 sec
390 sec
42Transfer ON timing control (Setting the time to transfer ON)
(Operation / Procedure)
1.When this simulation is executed, the currently set code number is displayed.
2.Enter the code number and press the START key, and the setting will be changed. (For any number different
from the following ones, the default time is automatically set.)
Code numberSetting
0Default (330 msec)
1-40msec
2-30msec
3-20msec
4-10msec
5Default (330 msec)
6+10msec
7+20msec
8+30msec
9+40msec
10-6