CD-BK100W/CD-BP90W
Setting the Clock (For CD-BK100W)
4Press the TUNING/TIME ( or ) button to adjust the hour and then
press the MEMORY/SET button.
Press the TUNING/TIME ( or ) button once to advance the time by 1 hour.
Hold it down to advance continuously.
When the 12-hour display is selected, "AM" will change automatically to "PM".
5Press the TUNING/TIME ( or ) button to adjust the minutes and then
press the MEMORY/SET button.
In this example, the clock is set for the 24-hour (0:00) display.
1Press the ON/STAND-BY button to turn the power on.
Press the TUNING/TIME ( or ) button once to advance the time by 1
minute. Hold it down to change the time in 5-minute intervals.
2Press the CLOCK button and within 5 seconds, press the MEMORY/
SET button.The hour will not advance even if minutes advance from "59" to "00".
The clock begins counting from "0" seconds. (Seconds are not displayed.)
The time display will disappear after a few seconds.
To confirm the time display:
Press the CLOCK button.
The timei dsplay will appear for about 5 seconds.
3Press the TUNING/TIME ( or ) button to select 24-hour or 12-hour
display and then press the MEMORY/SET button.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button when the AC power
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
"0:00"The 24-hour display will appear.To readjust the clock:
(0:00 - 23:59)Perform "Setting the Clock" from the beginning. If the time display is flashing, step 3
"AM 12:00"The 12-hour display will appear.(for selecting the 24-hour or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display: (AM 12:00 - PM 11:59)
"AM 0:00"The 12-hour display will appear.1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)".]
(AM 0:00 - PM 11:59)2 Perform "Setting the Clock" from the beginning.
Note that this can only be setunit when is the first installed or it has been reset.
[Refer to "Clearing all the mem)".] ory (reset
Setting the Clock (For CD-BP90W)
4Press the TUNING/TIME ( or ) button to adjust the hour and then
press the MEMORY/SET button.
Press the TUNING/TIME ( or ) button once to advance the time by 1 hour.
Hold it down to advance continuously.
When the 12-hour display is selected, "AM" will change automatically to "PM".
5Press the TUNING/TIME ( or ) button to adjust the minutes and then
press the MEMORY/SET button.
In this example, the clock is set for the 24-hour (0:00) display.
1Press the ON/STAND-BY button to turn the power on.Press the TUNING/TIME ( or ) button once to advance the time by 1
2Press the CLOCK button and within 5 seconds, press the MEMORY/minute. Hold it down to change the time in 5-minute intervals.
SET button.The hour will not advance even if minutes advance from "59" to "00".
The clock begins counting from "0" seconds. (Seconds are not displayed.)
The time display will disappear after a few seconds.
To confirm the time display:
Press the CLOCK button.
The timei dsplay will appear for about 5 seconds.
3Press the TUNING/TIME ( or ) button to select 24-hour or 12-hour
display and then press the MEMORY/SET button.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button when the AC power
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
"0:00"The 24-hour display will appear.To readjust the clock:
(0:00 - 23:59)Perform "Setting the Clock" from the beginning. If the time display is flashing, step 3
"AM 12:00"The 12-hour display will appear.(for selecting the 24-hour or 12-hour display) will be skipped.
(AM 12:00 - PM 11:59)
To change the 24-hour or 12-hour display:
"AM 0:00"The 12-hour display will appear.1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)".]
(AM 0:00 - PM 11:59)2 Perform "Setting the Clock" from the beginning.
Note that this can only be setunit when is the first installed or it has been reset.
[Refer to "Clearing all the mem)".] ory (reset
� 8 � |
ACEC
