CX68K5
SX68K7
CUT OFF POINT
analyzer CA-100 in adjustment
WAVEFORM OR OTHERSthe remote controller.the left) black of the window pattern to sink.
pattern) or equivalent signal is received.
*When E-2 CH (Crosshatch 1. Make the image normal with 2. Adjust the 3rd (1 thru 5 from Note1 : Use "Y" of Minolta color
A with
?
50
?
A or more for 30
?
509-2
?
3cd.
?
0.3cd.
?
beam current 1,500min or more.
mode.controller.& TP1602. Ammeter full scale-3mA range TP1602 is connected at the - side of the ammeter. TP1601 is connected at the + side of the ammeter.R1759 (sub-contrast VR).controller.the remote controller, and adjust the right dark white area of the window pattern to 2.7cdcontroller.with the remote controller, and adjust 50% white to 110
ADJUSTMENT CONDITION / PROCEDURE
(1) Receive (Monoscope pattern) with standard (2) Make the image normal with the remote (3) Connect the beam ammeter between TP1601 (4) Adjust the beam current to 1.6mANote : Apply the adjustment after aging with the (On the white or green monocolor screen)(1) Receive the window pattern with AV input. (2) Make the image normal with the remote (3) Select the sub-bright adjustment mode with (1) Receive the window pattern with AV input. (2) Make the image normal with the remote (3) Select the SUB-CONTRAST adjustment mode
CUT OFF, BKGD, SUB-CONT ADJUSTMENTC BUS CONTROL)
2C BUS
2I
ADJUSTMENT POINTR1759SUB-BRIGHTNESS ADJUSMENT (I(RF SIGNAL)SUB-CONTRASTADJUSTMENT (RF SIGNAL)
3MAX BEAM45
NO
DOWN"4"KEYDOWN "5"KEYDOWN"6"KEY
Y : 0.275
DOWN "KEYDOWN "0"KEY
°K X : 0.272
WAVEFORM OR OTHERS
On the monocolor screen of white or green.Note1: R CUT OFF UP"1"KEYG CUT OFF UP"2"KEYB CUT OFF UP"3"KEYData up/down is possible with the above comparison. *12,300(With Monolta color thermometer CA-100) Note1: G-DRIVE UP "7"KEYB-DRIVE UP"8"KEYData up/Down is possible with the above comparison. *The color temperature is based on the shipment initial setting table.
A or more
?
50
?
A or more for 30 9-1
?
50
?
the beam current 1,500for 30 min or more.
beam current 1,500min or more. (On the white or green minocolor screen)
signal.service mode.select the lateral in-line mode.first lighting lateral in-line raster to slighly light.and coarsely adjust the lateral in-line to become white. (Note 1)the point where the lateral in-line raster goes out. Note 1: Apply the adjustment after aging with select the normal mode.BURST Signal.and TP1602.1.6mA with R1759 (Sub-Contrast VR)(PAL burst is generated with the signal generator.)the color temperature 12,300K of the white peak to white.12,300K with R-cut off, G-cut off and B-cut off.peak.
ADJUSTMENT CONDITION / PROCEDURE
(1) Receive "WHITE" Pattern with Color Burst (2) Select P-NORM with the remote controller. (3) Select the CUT OFF BKGD mode at the (4) Select the screen VR 0/10. (5) Press "-/--" key of the remote controller to (6) Turn the scteen VR clockwise, and adjust the (7) Adjust the CUT OFF data of two other colors, (8) Turn the screen VR in the opposite direction to (9) Press "-/--" key of the remote controller to (1) Receive "WHITE" Pattern with COLOR (2) Select P-NORM with the remote controller. (3) Connect the beam ammeter between TP1601 (4) Coarsely adjust the beam current to approx. (5) Receive the window pattern with AV input.(6) With the data of G-drive and B-drive, adjust (7) Adjust the right dark area of the window to (8) Read just the color temperature at the white (9) Check 12,300K at the low white. Note1 : Apply this adjustment after aging with the
CUT OFF, BKGD, SUB-CONT ADJUSTMENT2C BUS C BUS
ADJUSTMENT POINTCRT CUTOFF ADJUSTMENT (ICONTROL)WHITE BALANCE BACKGROUND2IADJUSTMENT (RF SIGNAL)
12
NO
9 |
ACEC
