SECTION 1
The instructions given here are partial abstracts from the Operating Instruction
GENERALManual. The page numbers shown reflect those of the Operating Instruction Manual.
Table of ContentsAdjustments
Precautions ...............................................................................3Damper Wire..........................................................................6
Getting Started .........................................................................3Use of the Tilt-Swivel............................................................7A number of digital controls are provided to allow you to
Adjustments.............................................................................. 4Specifications..........................................................................7optimize the display parameters to your preferences.
Power Saving Function...........................................................6Troubleshooting.....................................................................7You can adjust the picture to your preferences by followingPOWERSAVING
Plug and Play ...........................................................................6the procedure described below.
You can adjust all items on the OSD (On Screen Display).
Push this part to open the control panel cover.
Precautionsp Adjustments will be stored automatically.
p The OSD automatically disappears 3 seconds after you
release the buttons.
InstallationWarning on Power Connection
Control Panel
? Prevent internal heat buildup by allowing adequate air? Use the supplied power cord.
circulation. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials (curtains, draperies) that
may block the ventilation holes.
? Do not install the unit near heat sources such as radiatorsPOWERSAVING
for 100 to 120 V ACfor 220 to 240 V ACRESET
or air ducts, or in a place subject to direct sunlight,
excessive dust, mechanical vibration or shock.For the customers in U.S.A.
? Do not place the unit near equipment that generatesIf you do not do this, this monitor will not conform to
ContrastHorizontal centering
magnetism, such as a converter or high-voltage powermandatory FCC standards.
lines.? Before disconnecting the power cord, wait for at leastThe adjustment data becomes the common setting for allThe adjustment data becomes the unique setting for the
30 seconds after turning off the power switch to allow for theinput signals.input signal received.
discharging of static electricity on the CRT display surface.EN
N 5 NMaintenance? After the power has been turned on, the CRT is1Press the >+/� button.1Press the So/o button.
demagnetized for approximately 5 seconds. ThisThe > OSD (On Screen Display) appears.The S OSD (On Screen Display) appears.
Clean the cabinet, glass panel, and controls with a soft cloth,generates a strong magnetic field around the bezel, which
lightly moistened with a mild detergent solution. Do not usemay affect the data stored on magnetic tape or disks near
any type of abrasive pad, scouring powder, or solvent, suchthe bezel. Place such magnetic recording equipment and
as alcohol or benzine.tapes/disks at a distance from this unit.
TransportationThe socket-outlet shall be installed near the equipment
and shall be easily accessible.
When you transport this monitor for repairing or shipping,2Press the >+/� button to adjust picture contrast.2Press the So/o button.
use the original carton box and packing materials.+....for more contrasto ... to move right
�....for less contrasto ... to move left
Getting StartedBrightnessVertical centering
The adjustment data becomes the common setting for allThe adjustment data becomes the unique setting for the
Before using this monitor, make sure that the followingStep 2: Attach the power cord to the monitor and then toinput signals.input signal received.
items are included in your package:the power outlet.
the monitor, power cord and this operating instruction1Press the ?+/� button.1Press the s�/A button.
manual.The ? OSD (On Screen Display) appears.The s OSD (On Screen Display) appears.
This monitor will sync to platforms running at horizontal
frequencies between 30 and 70 kHz.
Connecting the Computer
Step 1: With the computer switched off, attach the video
signal cable to the video output.
to the powerPower cord (supplied)
outlet2Press the ?+/� button to adjust picture brightness.2Press the s�/A button.
Computer+....for more brightnessStep 3: Turn on the monitor and computer.� ...to move up
�....for less brightnessA ...to move down
Step 4: If necessary, adjust the user controls according to
to the video outputyour personal preference.
The installation is complete.A-700T
34 |
ACEC
