LOADING AGING MODETITLE MEMO SHIFT MODE
Y This mode is used for repeating loading operations continuouslyY This mode is used for writing title memo information recorded.
Y Aging will be performed continuously unless an error occurs.in this unit in a different unit.
Y When an error occurs, the error code will be displayed on theUse it for transferring disc memo contents written by the cus-
fluorescent indicator tube.tomer to the new units when replacing the unit, etc.
Connection:
Flow of data
Procedure:r
1. Set a disc in the DISC 1 slit.
2. Turn on the power and press the GROUP FILE , MEGA CTRLThis unitAnother unit
rrr
and I/1 buttons.(Copy source)(Copy destination)
Rotate the DISC/CHARACTER knob, select OTable
Roatation� and press the dial.
3. When the mode is set, both the H and X indicators will
start to blink.
4. When the H button is pressedH, onl indicator willy the CONTROL A1 II connection cord provided
blink and aging starts.
CONTROL A1 II
5. To end the mode, prIess the /1 button or disconnect the
power cord from the outlet.
Procedure:
1. Connect two units using the CONTROL A1 II connection
The error codes displayed during operations and when errors oc-
cord shown in the figure.
cur are the same as the OAGING MODE� described earlier.
2. With the power on, while pressing the GROUP 7 button and
OPEN/CLOSE button of the copy destination unit, press the
TABLE AGING MODE
+100 button.
Y This mode is used for rotating the table randomly.
3. When the data has been transferred, the fluorescent indicator
Y Aging will be performed continuously unless an error occurs.
tube displays Ocomplete� for about 1 second.
Y When an error occurs, the error code will be displayed on the
fluorescent indicator tube.
MODEL NAME DISPLAY
Y Model names can be displayed on the fluorescent indicator tube
Procedure:for checking the microprocessor model setting, etc.
1. Turn on the power and press the GROUP FILE , MEGA CTRL
and I/1 buttons.Procedure:
Rotate the DISC/CHARACTER knob, select OTabWle ith the poAging� wer ON, while pressing the GROUP FILE and MEGA
and press the dial.CTRL buttons, press the I/1 button.
Rotate the DISC/CHARACTER knob and set the disk in theRotate the DISC/CHARACTER knob, select OModel Name�
slit whose number is being displayed (150, 149, 300, 1, 2)and press the dial.
2. When the mode is set, both the H and X indicators willThe model name is displayed on the fluorescent indicator tube.
start to blink.Let the model name be displayed for three seconds and exit the
3. When the H button is pressedH, onl indicator willy the mode.
blink and aging starts.
4. To end the mode, prIess the /1 button or disconnect theMICROPROCESSOR VERSION DISPLAY
power cord from the outlet.Y The microprocessor version can be displayed on the fluorescent
indicator tube.
During aging, operations will be carried out sequentially in the
order of No. 1, No. 2, No. 150, No. 149, and No. 300 slits.Procedure:
With the power ON, while pressing the GROUP FILE and MEGA
The error codes displayed during operations and when errors oc-CTRL buttons, press the I/1 button.
cur are the same as the OAGING MODE� described earlier. Rotate the DISC/CHARACTER knob, select OShow Mcom Ver.�
and press the dial.
DOOR POP UP AGING MODEThe microprocessor version is displayed on the fluorescent indi-
Y This mode is used for performing aging of the CD pop up partcator tube.
and door open/close.Let the model name be displayed for three seconds and exit the
It is used for checking if operations are perfmode.ormed normally.
Method:
1. Turn on the power and press the GROUP FILE , MEGA CTRL
and I/1 buttons.
Rotate the DISC/CHARACTER knob, select ODoor Popup
Aging� and press the dial.
2. Aging starts, and door open/close and up/down operations of
the pop up part are performed continuously.
3. To end the mode, press the I/1 button.
TABLE ROTATION MODE
Y This mode is used for electrical adjustments. Refer to the sec-
tion on Electrical Adjustments.
14 |
ACEC
