Locking the controls
Adjusting the convergence (CONV)Additional settings (OPTION)Helpful hints and information
To protect adjustment data by locking the controls, first
The CONV settings allow you to adjust the quality of the picture You can manually degauss (demagnetize) the monitor, adjust the move the control button m/M to select (CONTROL (HELP)
by controlling the convergence. The convergence refers to the moire cancellation level, change the menu position, and lock the LOCK). Then move the control button ,, to select ON.
alignment of the red, green, and blue color signals.controls.Only the 1 (power) switch, EXIT, and (CONTROL LOCK) The HELP menu contains helpful hints and information about this
If you see red or blue shadows around letters or lines, adjust the of the OPTION menu will operate. If any other items are selected, monitor. If your monitor is displaying symptoms that match those
convergence.1Press the center of the control button.the mark appears on the screen.listed in the HELP menu, follow the on-screen instructions to
These settings are stored in memory for all input signals.The main MENU appears on the screen.resolve the problem. If the symptoms do not match those listed in
To cancel the control lockthe HELP menu or if the problem persists, see OTrouble
1Press the center of the control button.2Move the control button to highlight OPTION and Repeat the procedure above and set (CONTROL LOCK) to OFF.symptoms and remedies� on page 16.
The main MENU appears on the screen.press the center of the control button again.
The OPTION menu appears on the screen.1Press the center of the control button.
2Move the control button to highlight CONV and The main MENU appears on the screen.
press the center of the control button again.3Move the control button m/M to select the desired
The CONVERGENCE menu appears on the screen.adjustment item.2Move the control button to highlight HELP and
Adjust the selected item according to the following press the center of the control button again.
3First move the control button m/M to select for instructions.The following HELP menu appears on the screen.
horizontal adjustment, or for vertical HELP
adjustment. Then move the control button </, to Degaussing the screen
RETURN TO MAIN MENU
adjust the convergence.The monitor is automatically demagnetized (degaussed) when the RECOMMENDED RESOLUTION
FLICKER
power is turned on.THIN HORIZONTAL LINE
DISTORTED SHAPE
To manually degauss the monitor, first move the OUT OF FOCUS
control button m/M to select (DEGAUSS). Then move DISCOLORATION
the control button ,.
The screen is degaussed for about 5 seconds. If a second degauss
3Move the control button m/M to select a HELP menu
cycle is needed, allow a minimum interval of 20 minutes for the
item and press the center of the control button
best result.US
again.
Instructions or information to resolve the problem appears on
Adjusting the moire*
the screen. An explanation of each menu item is given below.
If elliptical or wavy patterns appear on the screen, adjust the moire
cancellation level.RECOMMENDED RESOLUTION
To adjust the amount of moire cancellation, first move
If the picture does not fill the screen to the edges or if the picture
the control button m/M to select (MOIRE ADJUST). appears too large for the screen, adjust the resolution to the figures
Then move the control button </, until the moire shown in the menu using your computer. If the input signal
effect is at a minimum.
1-5matches one of this monitorOs factory preset modes, the resolution
and refresh rate of the current input signal are displayed.
* Moire is a type of natural interference which produces soft, wavy lines
on your screen. It may appear due to interference between the pattern RECOMMENDED RESOLUTION
of the picture on the screen and the phosphor pitch pattern of the SET RESOLUTION TO
monitor.1280X1024 AT 85Hz USING PC.
CURRENT SETTING IS
1280X1024 AT 75Hz.
Example of moire
FLICKER
If the picture is flickering, adjust the refresh rate to figures shown
in the menu. If the input signal matches one of this monitorOs
factory preset modes, the refresh rate of the current input signal is
displayed.
FLICKER
Changing the menuOs positionSET REFRESH RATE TO
75Hz OR 85Hz USING PC.
Change the menuOs position if it is blocking an image on the CURRENT SETTING IS 60Hz.
screen.
To change the menuOs on-screen position, first move
the control button m/M to select (OSD H POSITION)
for horizontal adjustment, or (OSD V POSITION) for
vertical adjustment. Then move the control button
</, to shift the on-screen menu.
(continued)
1213 |
ACEC
