HCD-DZ100
SECTION 4
TEST MODE
3. Disc Tray Lock
Note 1: Regarding the notification symbol OR�
Because the number of the operating buttons of this productThe disc tray lock function for the antitheft of an demonstration
are limited, some operations require use of the operatingdisc in the store is equipped.
buttons of the remote commander, When a specific operSetting Prationocedure :
requires use of the operating buttons of the remote1. Press the ?/1 button to turn the set on.
commander, OR� is added to the specific operating procedure2. Press the FUNCTION button to set DVD function.
in this manual. Example MENU/NO OR� The MENU/NO3. Insert a disc.
button of remote commander.
4. Press the x button and the A button simultaneously for five
Note 2: Incorrect operations may be performed if the test mode isseconds.
not entered properly.5. The message OLOCKED� is displayed and the tray is locked.
In this case, press the ?/1 button to turn the power off, and
retry to enter the test mode.Releasing Procedure :
1. Press the x button and the A button simultaneously for five
seconds. again.
1. Cold Reset2. The message OUNLOCKED� is displayed and the tray is
Y The cold reset clears all data including preset data stored inunlocked.
the RAM to initial conditions. Execute this mode whenNote:When OLOCKED� is displayed, the slot lock is not released by
returning the set to the customers.turning power on/off with the ?/1 button.
Procedure:
1. Press the ?/1 button to turn the power on.4. DVD Ship Mode
2. Press three b xuttons , A and ?/1 simultaneously.Y Use this mode when returning the set to the customer after
3. When this button is operated, display as OCOLD RESET� frepair.or
a while and all of the settings are reset.Procedure:
1. Press the ?/1 button to turn the set on.
2. Panel Test Mode2. Press the FUNCTION button to set the function ODVD�.
YThis mode is used to check the software version, LCD, LED3. Press three buttons x , and ?/1 simultaneously.
and keyboard.4. After a message OMECHA LOCK� is displayed on the
fluorescent indicator tube, pull out the AC plug.
2-1. DVD LED Test Mode5. To exit from this mode, press the ?/1 button to turn the set
Procedure:on.
1. Press the ?/1 button to turn on the power.
2. Press three bottons X , . and A simultaneously.5. DVD Debug In Mode
3. When the display LED test mode is activated, all seProcedure:gments
are turned on.1. Press the ?/1 button to turn the set on.
4. To exit from this mode, pull out the AC plug.2. Press the FUNCTION button to set the function ODVD�.
3. Press the three b.uttons , A and > simultaneously.
2-2. Version Test Mode4. To exit from this mode, press the ?/1 button to turn the set
Procedure:on.
1. When the panal test mode is acti.vated, press the button
and the message ***ODS1� is displayed, the version test mode6. AM Step Change
is activated.YA step of AM channels can be changed over between 9 kHz
2. Whenever press the . button, the version is displayed inand 10 kHz.
order of CC2, MC, SYS, UI, DVD, TA, TM and DS1.Procedure:
3. Press the > button and the date of the softwafe production1. Press ?/1 button to turn the set ON.
is displayed.2. Select the function OTUNER�, and press FUNCTION button
4. Press the > button again and the version is displayed.to select the BAND OAM�.
5. To exit from this mode, pull out the AC plug.3. Press ?/1 button to turn the set OFF.
4. Press > and ?/1 buttons simultaneously, and the display
2-3. Key Test Modeof fluorescent indicator tube changes to OAM 9 k STEP� or
Procedure:OAM 10 k STEP�, and thus the channel step is changed over.
1. When the panel test mode is actiHvated, press the button,
to select the key test mode.
2. To enter the KEY test mode, the fluorecent indicator displays
OK0 VO�. Each time a button is pressed, OKEY� value
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, OK8
VO � is displayed.
3. To exit from this mode, pull out the AC plug.
18 |
ACEC
