6-5. DRIVE MANUAL OPERATION0. Disc Check Memory
Disc Check
On the Test Mode Menu screen, select [2], and the manual opera-
tion menu will be displayed. For the manual operation, each servo
on/off control and adjustment can be executed manually.
1. SL Disc Check
## Drive Manual Operation ##2. CD Disc Check
3. DL Disc Check
Operation Menu
1. Disc type
2. Servo Control
3. Track/Layer Jump0. Reset SLED TILT
4. Manual Adjustment
5. Auto Adjustment
6. Memory Check
7. 5CHG Mecha Control
On this screen, the mirror time is measured and written to the
0. Disc Check Memory
EEPROM to check the disc type. First, set a DVD SL disc and
Exit: RETURNpress [1], then set a CD disc and pr[2], and fess inally set a DVD
DL disc and pr[3]ess . The measured mirror time is displayed re-
In using the manual operation menu, take care of the follospectively. wing
points. These commands do not provide protection, thus requiringThe adjustment must be executed more than once after default
correct operation. The sector address or time code fdata were written.ield is dis-
played when a disc is loaded.Reference value for DVD is from 10 to 20, and for CD, from 28 to
4F. Check that the value of CD is larger than that of DVD. When
1. Set correctly the disc type to be used on the Disc those values are beTypeyond a range perform this adjustment again.
screen.From this screen, you can go to another mode by pressing [NEXT]
The disc type must be set after a disc was loadedor [PREV]. key, but you cannot enter this mode from another mode.
The set disc type is cleared when the tray is opened.You can enter this mode from the Operation Menu screen only.
2. After power ON, if the Drive Manual Operation was se-
lected, first perform OReset SLED TILT� by opening 1.1. Disc Type
Disc Type screen.
3. In case of an alarm, immediatel[STOP]y press the but-Disc Type
1. Disc Type Auto Check
ton to stop the servo operation, and turn the power OFF.
2. DVD SL12 cm
3. DVD DL12 cm
Basic operation (controllable from front panel or remote com-
4. CD12cm
mander)
5. LCD12 cm
6. DVD SL8 cm
[POWER]Power OFF7. DVD DL8 cm
[STOP]Servo stop8. CD8 cm
[OPEN/CLOSE]Stop+Eject/Loading9. LCD8 cm
0. Reset SLED TILT
[RETURN]Return to Operation Menu or Test Mode
EMG. 00
Menu
[NEXT], [PREV]Transition between sub modes of menu
[1] to [9], [0]Selection of menu items
On this screen, select the disc type. To select the disc type, press
Cursor UP/DOWN Increase/Decrease in manually adjusted
the number of the loaded disc. The selected disc type is displayed
value
at the bottom. Selecting [1] automatically selects and displays the
[DISC SELECT]Selection of applicable number disc
disc type. In case of wrong display, retry ODisc Check Memory�.
[1] to [5]
Also, opening the tray causes the set disc type to be cleared. In
[DISC SKIP]Go to the next disc
this case, set the disc type again after loading.
[EXCHANGE]Open the disc tray while playing a disc
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Disc Type
1. Disc Type Auto Check
2. DVD SL12 cm
3. DVD DL12 cm
4. CD12cm
5. LCD12 cm
6. DVD SL8 cm
7. DVD DL8 cm
8. CD8 cm
9. LCD8 cm
0. Reset SLED TILT
SA.------ SI.-- EMG. 00
DVD SL 12 cm
Display when DVD SL 12cm disc was selected
6-7 |
ACEC
