SONY E280VC1 Repair Manual

$7.99

SONY E280VC1 - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

vedat kaya - 07/18/2008

i got my service manual for philips vr685-02. Thanks a lot for my very clear and net service manual. I will continue shopping from user-manual.com.

Mark Tarkett -

Excellent service, good price, products are excellent. Will do business with this vendor again.

Anny ROY - 04/06/2007

Super fast service and document of excellent quality. Thanks

Patrick Guice - 04/23/2008

Phenomal manual great resoulution and very legible. Will become very helpfull in future for parts and service.

John Craig - 07/31/2006

Very nice site and the manual is great. A life-saver. Thank you so much!

Customers who bought this product also purchased

SONY 14DK1 Service Manual	SONY AC-E45A Owner's Manual	SONY AC-E60A Owner's Manual
SONY 17VC Owner's Manual	SONY AC-E30A Owner's Manual	SONY 1401 Service Manual

Click to see text excerpt from the manual

3-18.TAPE SENSORS, REEL SENSOR
1 Photo diode
AND EP SW LEVERCut
(reel sensor)
3-18-1 TAPE TOP SENSOR AND TAPE END
SENSOR (See Fig. 3-18-1)
1) Refer to section 3-2 and remove the mechanism unit.Mounting shaft for
take up reel
2) Refer to section 3-3-1 and remove the cassette mecha-
assembly
nism assembly.
3) Remove the soldering from the MC-1 PWB assembly,
then remove the photo diodes 1, 2 and the LED 3.
When removing the photo diode 2 on the tape top
sensor side, refer to section 3-15 and remove the main
cam.
ASSEMBLY NOTES:
1. Fit the photo diodes 1 and 2 so that their photorecep-
2 Protrusion
tors to face the LED 3, as shown in Fig. 3-18-1. Align
the cuts in the LED 3 and the holder 4.
Push the photo diodes 1, 2 and the LED 3 as far
down as they will go, so that they do not protrude above
the top of their holders.
2. Do the soldering quickly.
Fig. 3-18-2
Turn the photoreceptors to
face the LED 3
3-18-3. EP SWITCH LEVER (See Fig. 3-18-3)
1) Refer to section 3-3-1 and remove the cassette mecha-
1 Photo2 Photo
nism assembly.
diode diode
2) Remove the EP switch spr1.ing
(Tape end (Tape top
sensor) sensor)3) Remove the clamp 2, then remove the EP switch lever
3.
3 LEDASSEMBLY NOTES:
1. Apply grease (VHJ-0100) to the protr4 on theusion
Align the cuts
back of the EP switch le3. ver
2. After fitting the cassette mechanism assembly. check
HoldersHolders
that in EJECT mode. the EP switch le3 does notver
4 Holder
touch the EP switch 5 .
1 EP switch spring
Front3 EP switch lever
Fig. 3-18-1
4 Protrusion on2 Clamp
back
3-18-2. REEL SENSOR (See Fig. 3-18-2) (apply grease here)
1) Refer to sections 3-12-2 and 3-12-4. then remove the
clutch mounting assembly, the T soft brake assembly
and the take up reel assembly.
2) Refer to section 3-13-2, then remove the wheel gear 2,
the wheel gear 1. and the brake control lever.
3) Remove the soldering from the MC-1 PWB assembly,
then remove the photo diode (reel sensor) 1.
ASSEMBLY NOTES:
5 EP switch
1. When assembling the parts, align the cut on the photo
diode (reel sensor) 1 with the protrusion on the
mechanism chassis 2.
2. Do the soldering quickly. Fig. 3-18-3
5-25