HCD-DX10/RG4SR/RG20/RG30T
SECTION 3
TEST MODE
[Change-over of AM Tuner Step between 9 kHz and2) Error display
10 kHz]Disc error
Y A step of AM channels can be changed over between 9 kHz andDisplayError
10 kHz.
E00D01022Focus error (No disc)
E00D02022Sub Q error (Focus is good)
Procedure:E00D02023TOC reading error
1. Press?/1 button to turn the set ON.
2. Select the function TUNER, and press TUNER/BE00D02014ANDAccess error (Unable within regular time)
button to select the BAND OAM.
3. Press?/1 button to turn the set OFF.Mechanism error
4. Press TUNER/BAND and?/1 buttons simultaneously, andDisplayError
the display of fluorescent indicator tube changes to AM 9 k
E00M__E_0Error during opening tray
STEP or AM 10 k STEP, and thus the channel step is changedE00M__C_2EX-CHANGE disc error
over.
E00M__D_0Error during closing tray
[Cold Reset]E00M__F_3EX-OPEN error
Y The cold reset clears all data including preset data stored in theE00M__D_5EX-CLOSE error
RAM to initial conditions. Execute this mode when returningE00M__C_2Chuck-up error
the set to the customer.E00M__C_3Unchucking error
Procedure:
1. Press three bxuttons , DISPLAY , and?/1 simultaneously.3. Aging mode in Tape Deck section
2. The fluorescent indicator tube displays COLD RESET and1) Operation during aging mode
the set is reset.Y In the agining mode, the program is excuted in the following
sequence.
[Aging Mode]StepOperationDisplay
This mode can be used for operation check of CD section and tape1Rewind the TAPE ATAPEAAG-1
deck section.
Y If an error occurred:2Rewind the TAPE BTAPEBAG-2
The aging operation stops and is displayed status.3Play the TAPE A (1 minute)TAPEAAG-2
Y If no error occurs:4Stop the TAPE A (1 second)TAPEAAG-3
The aging operation continues repeatedly.5Play the TAPE A (3 minutes)TAPEAAG-4
6Rewind(AMS) the TAPE ATAPEAAG-5
1. Operating method of Aging Mode7F.F.(AMS) the TAPE ATAPEAAG-6
Turn on the main power and select CD of the function.
1) Set three discs in tray. Select ALL DISCS, and REPEAT OFF.8Play the TAPE B (1 minute)TAPEBAG-2
2) Load the tapes recording use into both decks.9Stop the TAPE B (1 second)TAPEBAG-3
3) Press three bxuttons, DISPLAY , and10Record the TAPE B (3 minutes)TAPEBAG-4
DISC SKIP EX-CHANGE simultaneously.11Rewind(AMS) the TAPE BTAPEBAG-5
4) Aging operations of CD and tape are started at the same time.12F.F.(AMS) the TAPE BTAPEBAG-6
5) To exit the aging mode, perform [Cold Reset].
2) Error display
2. Aging mode in CD sectionY If error occurred, the display remains like TAPE BAG-2.
1) Operation during aging mode
Y In the agining mode ,the program is excuted in the f4. Exiting from the aging modeollowing
sequence.Y Be sure to perform Cold Reset to exit from the aging mode.
(1) The disc tray opens and closes.
(2) The disc tray turns to select a disc 3.
(3) The pickup accesses to the first track, and plays 3 seconds.
(4) The pickup accesses to the last track, and plays 3 seconds.
(5) The disc tray opens and closes.
(6) The disc tray turns to select a disc 1.
(7) The same operation starts like step (3).
(8) After a disc 1 aging operation, a disc 2 is selected.
(9) When an aging operation of a disc 3 is completed, the display
OAGING value increases.
(10) If no error occurs, the aging operation continues repeatedly.
11 |
ACEC
