Installation and Connections
Before installing or connecting the unit, pleaseARRANGE THE WIRING SO IT IS NOT CRIMPED OR
read the following and pages 2 and 3 of thisPINCHED BY A SHARP METAL EDGE.
manual thoroughly for proper use.
Route the cables and wiring away from moving parts (like
the seat rails) or sharp or pointed edges. This will prevent
Warningcrimping and damage to the wiring. If wiring passes through
a hole in metal, use a rubber grommet to prevent the wire's
MAKE THE CORRECT CONNECTIONS.insulation from being cut by the metal edge of the hole.
Failure to make the proper connections may result in fireDO NOT INSTALL IN LOCATIONS WITH HIGH
or product damage.MOISTURE OR DUST.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVEAvoid installing the unit in locations with high incidence
of moisture or dust. Moisture or dust that penetrates into
GROUND.
(Check with your dealer if you are not sure.) Failure to dothis unit may result in product failure.
so may result in fire, etc.
Precautions
BEFORE WIRING, DISCONNECT THE CABLE FROM
THE NEGATIVE BATTERY TERMINAL." Be sure to disconnect the cable from the (�) battery post
before installing your unit. This will reduce any chance of
Failure to do so may result in electric shock or injury duedamage to the unit in case of a short-circuit.
to electrical shorts." Be sure to connect the colour coded leads according to the
DO NOT SPLICE INTO ELECTRICAL CABLES.diagram. Incorrect connections may cause the unit to
malfunction or damage to the vehicle's electrical system.
Never cut away cable insulation to supply power to other" When making connections to the vehicle's electrical
equipment. Doing so will exceed the current carrying
system, be aware of the factory installed components (e.g.
capacity of the wire and result in fire or electric shock.on-board computer). Do not tap into these leads to provide
DO NOT DAMAGE PIPE OR WIRING WHENpower for this unit. When connecting this unit to the fuse
box, make sure the fuse for the intended circuit of the unit
DRILLING HOLES.
has the appropriate amperage. Failure to do so may result
When drilling holes in the chassis for installation, takein damage to the unit and/or the vehicle. When in doubt,
precautions so as not to contact, damage or obstruct pipes,consult your ALPINE dealer.
fuel lines, tanks or electrical wiring. Failure to take such" This unit uses female RCA-type jacks for connection to
precautions may result in fire.other units (e.g. amplifier) having RCA connectors. You
may need an adaptor to connect other units. If so, please
DO NOT USE BOLTS OR NUTS IN THE BRAKE ORcontact your authorized ALPINE dealer for assistance.
STEERING SYSTEMS TO MAKE GROUND" Be sure to connect the speaker (�) leads to the speaker (�)
terminal. Never connect left and right channel speaker
CONNECTIONS.
cables to each other or to the vehicle body.
Bolts or nuts used for the brake or steering systems (or
any other safety-related system), or tanks should NEVERIMPORTANT
be used for installations or ground connections. UsingPlease record the serial number of your unit in the
such parts could disable control of the vehicle and causespace provided below and keep it as a permanent
fire etc.record. The serial number plate is located on the
bottom of the unit.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT
HINDER VEHICLE OPERATION, SUCH AS THE
SERIAL NUMBER:
STEERING WHEEL OR GEARSHIFT.
INSTALLATION DATE:
Doing so may obstruct forward vision or hamperINSTALLATION TECHNICIAN:
movement etc. and results in serious accident.PLACE OF PURCHASE:
Caution
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
The wiring and installation of this unit requires special
technical skill and experience. To ensure safety, always
contact the dealer where you purchased this product to
have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL
THEM SECURELY.
Be sure to use only the specified accessory parts. Use of
other than designated parts may damage this unit internally
or may not securely install the unit in place. This may cause
parts to become loose resulting in hazards or product failure.
20-EN |
ACEC
