Troubleshooting Guide
Tips and advice Before starting a wash programme, Select a new programme and press the
Arrange crockery so that items do nomake sure thatt the spray arms can tuStrn art button.
AFTER-SALES
touch each other. Arrange large freely and are not impeded by croCrockery ckery still dirty after washing:
crockery in the lower rack and smalor culer tlery. Was the crockery loaded properly?SERVICE
crockery in the upper rack. Only switch off the dishwasher once theCrockery must be loaded facing
Load cups at an angle to facilitate? Star?t indicator lamp has switched off.downwards; this is important, espIefci afteallyr ca rrying out the above checks the
water drainage.If the dishwasher is switched off during a for large items of crockery.malfunction persists or appears again,
turn the appliance off and turn off the
Generally speaking, place cutlery inwash cycle, whe the n switched on again it The water jets must spray the entire water supply tap, then call our After-Sales
surface of all items.
basket with the handles positioned will resume the cycle from where it was Service (see guarantee). Please specify:
downwards, but ensure that any sharintep rrupted without having to start Make sure it that crockery and cutlery are The nature of the fault.
arranged properly.
knives and forks that might cause again.
Have you selected the correct program Tmhe? e appliance type and model.
injury are placed in the basket with the
Did you use too much or too little The service code (the number after the
handles positioned upwards.
detergent? (The use of poor quality word Service on the adhesive rating plate)
Make sure the water jet can reach all
detergents may result in less effective inside the door on the right-hand side.
loaded items and that the spray arms If a fault occurs, before contacting our
washing).
turn freely.After-Sales Service, make the following
checks to try and remedy the problem:Are the filters clogged or incorrectly
Important
assembled? (See ?Care and
Fill the detergent dispenser and chTheeck dishwasher is not working:
Maintenance? chapter in the user
the salt and rinse aid level. Is the plug properly inserted in the wall Your full address and telephone number.
instructions).
Do not use the appliance for items nosockett ?
Are the spray arms blocked or the nozzles
suitable for washing in a dishwash er,Is th ere a power failure?clogged? (See?Ca re and Maintena?nce
for example: wooden items, aluminium,Is th e dishwasher switched on?chapter in the user instructions).
plastic utensils, tin, hand-decora teHad s the Start button been pressed?Is the lower spray arm correctly fitted?
crockery (unglazed), silver cutlery.
Has the delayed start timer been set Is (if the sal t container cap (water softening
Do not put liquid fat in the dishwasfithetred )?system) screwed down?
(e.g. oil used for frying) or candle Is thwax.e water supply tap on? Marked crockery:
If a fault occurs or you wish to chan Is thge e flow of water obstructed by Is the water hardness level selector not
the current programme, press the properly adjusted? (See?Filli ng the salt
impurities? If so, close the water supply
?START ? button for about 5 seconds until tap, detach the water hose and cleanco thntae ine? inr the user instructions).
the Start indicator lamp switches off.filter. Then re-connect the water h Iosse thto e salt container emp?tFiy?lli (Seeng
If regeneration salt is to be addedthe, tap and open the water tap once the salt cont?ai inne thr e user
immediatel starty a wash programme again.instructions).
in order to eliminate any residual sa Arelt th e filters clogge?Cad? (Seere and Was insufficient detergent used? (See
(rinsing alone is not sufficient).maintenance? chapter in the user ?Filling the detergent di? in spethense r
Sometimes even though the instructions).user instructions).
regeneration salt container has beeIs thn e door closed properly?Marked glasses and cutlery:
filled, the corresponding indicator lamp Was too much rinse aid used? (See
Is a fault indicated?
(if fitted) will light up during the first ?Filling the rinse aid di? inspe thne seuser r
(The Start indicator lamp flashes).
wash cycle after filling with salt.instructions).
Start the programme again from the
Note: With some models, when the Start
beginning: Press the Start button for
button is pressed a pre-wash cycle precedes
about 5 seconds, until the Start indicator
the actual wash programme; this regenerates
lamp switches off.
the water softening system.
Please read the user instructions carefully. |
ACEC
