Operation Guide 3358/3368/3798
AlarmsIllumination
You can set five independent Daily Alarms. When anThis watch has an EL (electro-luminescent) panel that causes the entire display to
Alarm timealarm is turned on, the alarm tone sounds when the alarmglow for easy reading in the dark. The watchOs auto light switch automatically turns on
(Hour : Minutes) time is reached. One of the alarms is a snooze alarm,illumination when you angle the watch for reading towards your face.
Alarm number while the other four are one-time alarms." The auto light switch must be turned on (indicated by the auto light switch indicator)
You can turn on an Hourly Time Signal that causes thefor it to operate.
watch to beep twice every hour on the hour." See OIllumination Precautions� for more important information.
" There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers fromAuto light switch indicator
AL1through AL4), one is for a snooze alarm
(indicated by SNZ), and one is for the Hourly Time
Signal (indicated by SIG).
" All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
On/Off status
Module 3358Module 3368Module 3798
To set an alarm time
1.In the Alarm Mode, use D to scroll through the alarm
To illuminate the display
screens until the one whose time you want to set isIn any mode, press B to turn on illumination.
displayed.
" The above operation turns on illumination regardless of the current auto light switch
setting.
" You can use the procedure below to select either one second or three seconds as
the illumination duration. When you press B, the illumination will remain on for
about one second or three seconds, depending on the current illumination duration
setting.
" To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1through AL4. To set the snooze alarm, display the screen indicatedTo specify the illumination duration
by SNZ.1.In the Timekeeping Mode, hold down A until the
" The snooze alarm repeats every five minutes.seconds start to flash, which indicates the setting
2. After you select an alarm, hold down A until the hour setting of the alarm timescreen.
starts to flash, which indicates the setting screen.2.Press C nine times so the illumination duration setting
" This operation automatically turns on the alarm.screen is on the display.
3. Press C to move the flashing between the hour and minute settings.3.While the illumination duration setting is flashing, press
4. While a setting is flashing, use D (+) and B (�) to change it.D to toggle the setting between one second ( ) and
" When setting the alarm time using the 12-hour format, take care to set the timethree seconds ( ).
correctly as a.m. (no indicator) or p.m. (P indicator).4.Press A to exit the setting screen.
5. Press A to exit the setting screen.
Alarm OperationAbout the Auto Light Switch
The alarm sounds at the preset time for about 20 seconds, regardless of the mode theWhile the auto light switch is enabled, illumination turns on whenever you position
watch is in. In the case of the snooze alarm, the alarm operation is performed a totalyour wrist as described below in any mode.
of seven times, every five minutes, or until you turn the alarm off.
" Alarm and Hourly Time Signal operations are performed in accordance with theMoving the watch to a position that is parallel to the ground and then tilting it
Timekeeping Mode digital time.towards you at more than 40 degrees causes illumination to turn on.
" To stop the alarm tone after it starts to sound, press any button.
" Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.Parallel to groundMore than 40°
Displaying the Timekeeping Mode setting screen
Displaying the SNZ setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
Warning!
To turn an alarm on and off""""" Always make sure you are in a safe place whenever you are reading the watch
1. In the Alarm Mode, use D to select an alarm.using the auto light switch. Be especially careful when running or engaged in
2. Press A to toggle it on (ON displayed) and off (OF displayed).any other activity that can result in accident or injury. Also take care that
" Turning on a one-time alarm (AL1through AL4) causes the alarm on indicator tosudden illumination by the auto light switch does not startle or distract others
appear on its Alarm Mode screen. In all other modes, the alarm on indicator isaround you.
displayed when one or more of the alarms is turned on.""""" When you are wearing the watch, make sure that its auto light switch is turned
" Turning on the snooze alarm (SNZ) displays the alarm on indicator and snoozeoff before riding on a bicycle or operating a motorcycle or any other motor
alarm indicator on the Alarm Mode snooze alarm screen, and in all other modes.vehicle. Sudden and unintended operation of the auto light switch can create
" The alarm on indicator flashes while the alarm is sounding.a distraction, which can result in a traffic accident and serious personal injury.
" The snooze alarm indicator flashes during the 5-minute intervals between alarms.
To turn the auto light switch on and off
Snooze alarm indicator Alarm on indicator Snooze alarm indicator Alarm on indicator In any mode, hold down B for about two seconds to toggle the auto light switch on
(auto light switch indicator displayed) or off (auto light switch indicator not displayed).
" The auto light switch indicator is on the display in all modes while the auto light
On/Off switch is turned on.
status " In order to protect against running down the battery, the auto light switch
automatically turns off approximately six hours after you turn it on.
Module 3358Module 3368Module 3798
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time Signal (SIG).
2. Press A to toggle it on (ON displayed) and off (OF displayed).
" The Hourly Time Signal on indicator is shown on the display on the Alarm Mode
Hourly Time Signal screen, and in all other modes while the Hourly Time Signal is
turned on.
On/Off status Hourly time signal on indicator
Module 3358Module 3368Module 3798
3 |