Operation Guide 3007
StopwatchAlarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
The stopwatch lets you measure elapsed time, split times,watch is in. In the case of the snooze alarm, the alarm operation is performed a total
Minutes Seconds and two finishes.
of seven times, every five minutes, or until you turn the alarm off.
" The display range of the stopwatch is 59 minutes," To stop the alarm tone after it starts to sound, press any button.
59.99 seconds." Performing any one of the following operations during a 5-minute interval between
" The stopwatch continues to run, restarting from zerosnooze alarms cancels the current snooze alarm operation.
after it reaches its limit, until you stop it.Displaying the Timekeeping Mode setting screen
" The stopwatch measurement operation continues evenDisplaying the setting screen
if you exit the Stopwatch Mode.
" Exiting the Stopwatch Mode while a split time is frozenTo test the alarm
on the display clears the split time and returns toIn the Alarm Mode, hold down D to sound the alarm.
elapsed time measurement.
1/100 second " All of the operations in this section are performed in theTo turn an alarm on and off
Stopwatch Mode, which you enter by pressing C.1.In the Alarm Mode, use D to select an alarm.
Snooze alarm indicator 2.Press A to toggle it on ( displayed) and off
To measure times with the stopwatch( displayed).
" Turning on a one-time alarm ( through )
Elapsed Time
displays the alarm on indicator on its Alarm Mode
screen.
StartStopRe-startStopClear" Turning on the snooze alarm () displays the alarm
on indicator and snooze alarm indicator on the Alarm
Split Time Mode snooze alarm screen.
" In all modes, the alarm on indicator is shown for any
StartSplitSplit releaseStopClearalarm that is currently turned on.
On/Off status
( displayed) " The alarm on indicator flashes while the alarm is
Two FinishesAlarm on indicator sounding.
" The snooze alarm indicator flashes during the 5-minute
StartSplitStopSplit releaseClearintervals between alarms.
First runner Second runner Display time of
finishes.finishes.second runner.To turn the Hourly Time Signal on and off
Display time of 1.In the Alarm Mode, use D to select the Hourly Time
first runner.Signal ().
2.Press A to toggle it on ( displayed) and off
( displayed).
" The Hourly Time Signal on indicator is shown on the
Countdown Timerdisplay in all modes while the Hourly Time Signal is
The countdown timer can be set within a range ofturned on.
Hours Minutes one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
" The countdown operation continues even if you exit theOn/Off status
Countdown Timer Mode.Hourly time signal
" All of the operations in this section are performed in theon indicator
Countdown Timer Mode, which you enter by pressing
C.
To use the countdown timerIllumination
Press D while in the Countdown Timer Mode to start the
Seconds countdown timer.Two LEDs (light-emitting diodes) illuminate the display foreasy reading in the dark.
" When the end of the countdown is reached, the alarm
sounds for 10 seconds or until you stop it by pressingIllumination Precautions
any button. The countdown time is automatically reset to
" Illumination may be hard to see when viewed under
its starting value after the alarm stops.
direct sunlight.
" Press D while a countdown operation is in progress to pause it. Press D again to" Illumination automatically turns off whenever an alarm
resume the countdown.sounds.
" To completely stop a countdown operation, first pause it (by pressing D), and then" Frequent use of illumination runs down the battery.
press A. This returns the countdown time to its starting value.
To illuminate the display
To set the countdown start timeIn any mode (except when a setting screen is on the display), press B to turn on
1.In the Countdown Timer Mode, hold down A until theillumination.
hours of the countdown start time start to flash, which" You can use the procedure below to select either 1.5 seconds or 3 seconds as the
indicates the setting screen.illumination duration. When you press B, the illumination will remain on for about
2.Press C to move the flashing between the hours and1.5 seconds or 3 seconds, depending on the current setting.
minutes.
3.While a setting is flashing, use D (+) and B (�) toTo specify the illumination duration
change it.1.In the Timekeeping Mode, hold down A until the
" To set the starting value of the countdown time toseconds start to flash, which indicates the setting
24 hours, set .screen.
4.Press A to exit the setting screen.2.While the seconds are flashing, press B to toggle the
illumination duration between 1.5 seconds ( ) and 3
seconds ( ).
3.Press A to exit the setting screen.
Alarms
You can set five independent Daily Alarms. When an
Alarm number alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.Reference
You can turn on an Hourly Time Signal that causes theThis section contains more detailed and technical information about watch operation.
watch to beep twice every hour on the hour.It also contains important precautions and notes about the various features and
" There are six screens in the Alarm Mode. Four are forfunctions of this watch.
one-time alarms (indicated by numbers from
through ), one is for a snooze alarm (indicated byButton Operation Tone
), and one is for the Hourly Time Signal (indicated
The button operation tone sounds any time you press one
by ).
On/Off status " All of the operations in this section are performed in theof the watchOs buttons. You can turn the button operation
tone on or off as desired.
Alarm time Alarm Mode, which you enter by pressing C.
(Hour : Minutes) "Even if you turn off the button operation tone, the alarm,
Hourly Time Signal, and Countdown Timer Mode alarm
To set an alarm timeall operate normally.
1.In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set isTo turn the button operation tone on and off
displayed.In any mode (except when a setting screen is on the
display), hold down C to toggle the button operation tone
on ( not displayed) and off ( displayed).
" Holding down C to turn the button operation tone on or off also causes the watchOs
current mode to change.
" The indicator is displayed in all modes when the button operation tone is turned
" To set a one-time alarm, display one of the screens indicated by an alarm numberoff.
from through . To set the snooze alarm, display the screen indicated by
.Auto Return Features
" The snooze alarm repeats every five minutes." If you leave the watch in the Alarm Mode for two or three minutes without performing
2. After you select an alarm, hold down A until the hour setting of the alarm timeany operation, it automatically changes to the Timekeeping Mode.
starts to flash, which indicates the setting screen." If you leave a screen with flashing digits on the display for two or three minutes
" This operation turns on the alarm automatically.without performing any operation, the watch automatically saves any settings you
3. Press C to move the flashing between the hour and minute settings.have made up to that point and exits the setting screen.
4. While a setting is flashing, use D (+) and B (�) to change it.
" When setting the alarm time using the 12-hour format, take care to set the timeScrolling
correctly as a.m. ( indicator) or p.m. ( indicator).The B and D buttons are used in various modes and setting screens to scroll
5. Press A to exit the setting screen.through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
2 |