OPERATION CHART:MODULE QW-1455
GENERAL GUIDE
Y Press B to change from mode to mode.
Y After you perform an operation in any mode, pressing B returns to the Timekeeping Mode.
Y Holding down A at any time illuminates the display.
Y The backlight of this watch employs an electroluminescent (EL) light, which loses its illuminating power after very long term use.
Y Frequent use of the backlight shortens the battery life.
Timekeeping ModeAlarm ModeStopwatch ModeTime Setting Mode
APMsss
PM
BC
s
Timekeeping ModeStopwatch Mode
Day of the weekY In the Timekeeping Mode, press C to switchMode IndicatorThe Stopwatch Mode lets you measure elapsed time,
between the 12-hour and 24-hour formats.split times, and two finishes. The range of the stop-
PM indicatorDateY Day of the week is displayed as follows.watch is 59 minutes, 59.99 seconds.
A
SU:SundayMO:MondayTU:TuesdaySPLIT
APMWE:WednesdayTH:ThursdayFR:FridayBCSplit time indicator
SA:Saturday
BC
Minutes1/100 second
Seconds
Hour
Second
Minute
(a) Elapsed time measurement
CCCCA
StartStopRe-startStopClear
Alarm Mode
(b) Split time measurement
Hourly time signal on indicatorWhen the Daily Alarm is switched on, the alarm sounds
for 20 seconds at the preset time each day. When theCAACA
Mode indicatorStartSplitSplit releaseStopClear
Hourly Time Signal is switched on, the watch beeps
every hour on the hour.
A(c) Split time and 1st-2nd place times
To set the alarm time
BCCACAA
1. Hold down A while in the Alarm Mode until the hourStartSplitStopSplit releaseClear
digits start to flash on the display. The hour digitsFirst runnerSecond runnerRecord time of
Alarm onHourflash because they are selected.finishes.finishes.second runner.
indicatorMinutes2. Press A to change the selection in the followingRecord time of
sequence.first runner.
HourMinutes
Normal Alarm ModeTime Setting Mode
(No digit flashes)
To set the time and date
Day of the week1.Use B to enter the Time Setting Mode.
Y Once you reach the normal Alarm Mode, you have to hold down A again until the hourY The seconds digits flash because they are selected.
digits start to flash.2. Press A to change the selection in the followingPM indicatorDate
3. Press C to increase the selected digits. Holding down C changes the number at highsequence.
speed.A
PM
Y The format (12-hour and 24-hour) of the alarm time matches the format you select for
normal timekeeping.BCSecondsHourMinutes
Y When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon (PM).
4. After you set the alarm time, press A to return to the Alarm Mode. At this time theMinutesDay ofDateMonth
Daily Alarm is switched on automatically.HourSecondsWeek
To stop the alarm3. While the seconds digits are selected (flashing), press C to reset the seconds to O00�. If
you press C while the seconds count is in the range of 30 to 59, the seconds are reset to
Press A to stop the alarm after it starts to sound.
O00� and 1 is added to the minutes. If the seconds count is in the range of 00 to 29, the
minutes count is unchanged.
To switch the Daily Alarm and Hourly Time Signal on and off4. While any other digits (besides seconds) are selected (flashing), press C to increase the
number. While the day of the week is selected, pressing C advances to the next day.
Press C while in the Alarm Mode to change the status of the Daily Alarm and HourlyHolding down C changes the current selection at high speed.
Time Signal in the following sequence.
5. After you set the time and date, press B to return to the Timekeeping Mode.
[Alarm on Indicator/Hourly Time Signal on Indicator]Y If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
Both onBoth offDaily Alarm
Hourly Time
onlySignal only
To test the alarm
Hold down C while in the Alarm Mode to sound the alarm.
N 1 N |
ACEC
