2050-3
3. Use B and C to change the character at the cursor position in the text3. While hour or minutes is flashing, press C to increase the setting or B
area. The character changes in the following sequence.to decrease it.
? When setting the alarm time using the 12-hour format, take care to
Press C.Press B.set the time correctly as a.m. (no indicator) or p.m. (P indicator).
(space)A to Z0 to 9-4. Press A to return to the alarm display screen.
Daily Alarm Operation
)(/.
The alarm sounds at the preset time each day for about 20 seconds, or
4. When the character you want is at the cursor position, press M to moveuntil you stop it by pressing any button.
the cursor to the right.To test the alarm
5. Repeat the steps 3 and 4 until your text is complete.Hold down C to sound the alarm.
6. After you input text, use M to move the cursor to the number area.
? Holding down M for at least one second causes the cursor to jumpTurning the Daily Alarm and Hourly Time Signal on and off
between the text area and number area.In the Alarm Mode, press C to cycle through the on and off settings a
? The text area in the Identification Mode can hold up to 16 characters.shown below.
When the cursor is located at the 16th space of the text area, moving the
cursor to the right causes it to jump down to the first digit in the number[Alarm On Indicator / Hourly Time Signal On Indicator]
area. When the cursor is at the 10th digit of the number area, moving it to
ALM SIGALMSIG
the right causes it jump back up to the first character of the text area.
7. Use B and C to change the character (hyphen, number, or space) atAlarm OnAlarm OffAlarm OnAlarm Off
the cursor position in the number area. The character changes in theSignal OnSignal OffSignal OffSignal On
following sequence.
Press C.
x0 to 9(space)STOPWATCH MODE
Press B.
1/100 secondThe Stopwatch Mode lets you measure elapsed
8. When the character you want is at the cursor position, press M to movetime, split times, and two finishes. The range of
Mode indicator
the cursor to the right.the stopwatch is 23 hours, 59 minutes, 59.99
9. Repeat steps 7 and 8 until you complete number input.ABseconds.
10.Press A to store your data and return to the Identification Mode data
screen (without the cursor).
MALMSIGC
Inputting Your Blood Type
1. In the Identification Mode, display the
Rh factorHours : Minutes
Blood type ABOBLOOD TYPE title.
2. Hold down A until the blood type ABO startsSeconds
ABto flash.
3. Use B and C to scroll through the available(a) Elapsed Time
blood type in the following sequence.CCJJCJCJA
MALMSIGCStartStopRe-startStopClear
Press C.
(b) Split Time
-ABOAB
CAJJAJCJA
StartSplitSplit releaseStopClear
Press B.
4. Press M to advance to specification of the Rh factor.(c) Two Finishes
? At this time the current Rh factor (x or *) will flash on the display.JJJJ
CACAA
5. Press C to select either x (negative) or * (positive).
StartSplitStopSplit releaseClear
6. Press A to store your data and return to the BLOOD TYPE screen.
First runnerSecond runner finishes.Record time of
finishes.Record time of firstsecond runner.
Editing Identification Mode Data (except Blood Type Data)runner.
1. In the Identification Mode, scroll through the data and display the one
you want to edit.
2. Hold down A until the cursor appears in the text area.
3. Use M to move the cursor to the character you want to change.BACKLIGHT
4. Use B and C to change the character.
? For details on inputting characters, see OInputting Text and Numbers�Auto light switchThe backlight uses an EL (electro-luminescent)
(step 3 for text input and 7 for number).on indicatorpanel that causes the entire display to glow for
5. After making the changes that you want, press A to store them andeasy reading in the dark. The watchOs auto light
return to the Identification Mode data screen.switch automatically turns on the backlight when
AB
you angle the watch towards your face.
Deleting Identification Mode Data (except Blood Type Data)? The auto light switch must be turned on
PAUTOAUTO
1. In the Identification Mode, scroll through the data and display the one(indicated by the auto light switch on indicator)
ALMSIG
you want to delete.MCfor it to operate.
2. Hold down A until the cursor appears in the text area.
3. Press B and C at the same time to clear the data.Turning on the Backlight manually
? At this time the cursor appears in the text area, ready for input.In any mode, press B to illuminate the display for about two seconds.
4. Input data or press A to return to the Identification Mode data screen.? The above operation turns on the backlight regardless of the current
auto light switch setting.
About the Auto Light Switch
ALARM MODE
Turning on the auto light switch causes the backlight to turn on for about
You can set a Daily Alarm that sounds at theCurrent timetwo seconds, whenever you position your wrist as described below in any
same time each day, while it is turned on. mode.You
Mode indicator? See OBacklight Precautions� for other important information about using
can also turn on an Hourly Time Signal that
causes the watch to beep twice every hour onthe backlight.
ABthe hour.
PMoving the watch to a position that is parallel to the ground and then
Ptilting it towards you more than 40 degrees causes the backlight to light.
Setting the Alarm Time
MALMSIGC1. In the Alarm Mode, hold down A until the
hour digits of the alarm time start to flash.
More
? This operation automatically turns on the
Hour : MinutesParallel tothan
Daily Alarm.
Alarm on indicator2. Press M to move the flashing in the followingground40°
Hourly time signalsequence.
on indicator
HourMinutes |
ACEC
