Module No. 20502050-1
ABOUT THIS MANUAL
? Button operations are indicated using the? Make sure you correctly input your name and blood type data. Once
letters shown in the illustration.you input your data, take care that the watch is not borrowed by
AB
? Each section of this manual provides you withanother person. Otherwise, emergency medical personnel may
Pthe information you need to performassume that your data applies to the person who borrowed the
operations in each mode. Further details andwatch.
MSIGCALMtechnical information can be found in the? The default blood type screen setting when you first purchase the
OREFERENCE� section.watch or after you change the battery is O-� for the blood type and
(MODE)
ORh *� for the Rh factor. To avoid problems caused by display of
the wrong blood type, we recommend that you input your correct
Warning!blood type data as soon as possible after purchasing the watch
Note the following important points concerning Identification Mode dataand after having the battery replaced.
stored in the memory of this watch.? CASIO COMPUTER CO., LTD. shall not be held liable to you or any
? SCUBA diver certificate number, passport number, and emergencythird party for any losses or damages suffered through the misuse
contact number data stored in the memory of this watch can beof data stored in the memory of this watch.
misused whenever the watch is in the hands of another party.
? To protect against the misuse of SCUBA diver certificate number,
passport number, and emergency contact number data, input them
in coded form that cannot be understood by others.
GENERAL GUIDE
World Time ModeIdentification Mode
? Press M to change from mode to mode.
? While in any mode hold down M for one second, to enter the Dive Time
Measurement Mode.
? In any mode, press B to illuminate the display.
Ps
P
sALMSIGALMSIG
Dive Time
MeasurementTimekeeping Modes
Mode.
MStopwatch ModeAlarm Mode
ABPress Hold down M.
Ps
sPP
ssP
DIVETIMEALMSIGMALMSIGC
ALMSIGALMSIG
TIMEKEEPING MODEDIVE TIME MEASUREMENT MODE
In addition to normal timekeeping, use theThe Dive Time Measurement Mode lets you
Month � DayCurrent time
Timekeeping Mode to set the current time andmeasure the total time you spend underwater
Day of week
date. You can also view the Dive Timewhile diving or snorkeling, and the amount of
Mode indicator
Measurement Mode log data.time spent on the surface (surface interval). The
AB? For details on how to view the log data, seewatch also stores one set of diving time data
OViewing Log Data�.AB(total dive time and dive start time) into log
PPmemory for later recall.
MALMSIGCCalibrating the Seconds Count
1. In the Timekeeping Mode, hold down A untilMDIVETIMEALMSIGCWarning!
Hour : Minutesthe seconds digits start to flash.For your own safety, never operate the
2. Press C to set the seconds count to OO.Dive timebuttons of the watch while underwater or
Seconds
? Pressing C while the seconds count is inwhile on the waterOs surface. Perform button
PM indicatorthe range of 30 to 59 resets the seconds tooperations in a safe place after leaving the
OO and add 1 to the minutes. In the rangewater.
of 00 to 29, the minutes count is unchanged.
Before Diving/Snorkeling
3. Press A to return to the current time screen.
? Be sure to check if the battery power is low (check for low light
intensity, a dim display, or the flashing indicator). If it is, do not
Setting the Time and Date
use the watch for diving/snorkeling.
1. In the Timekeeping Mode, hold down A until
? Make sure that the watch is set to the correct time.
ABthe seconds digits start to flash.
? Check the glass, case and band for cracks or chips.
2. Press M to move the flashing in the
? Make sure that the band is fastened securely around your wrist.
Psequence shown below to select other
ALMSIGsettings.MCWhile Diving/Snorkeling
? Always use the Obuddy system� when diving � never dive alone.
? Check to make sure that timer operation is being performed properly.
12/24-Hour
SecondsHourMinutes? Take care when diving/snorkeling near rocks or coral to avoid
Format
scratching the watch.
DayMonthYear
After Diving/Snorkeling
To avoid corrosion, rinse your watch thoroughly with fresh water to
3. While hour, minutes, year, month, or day is flashing, press C to increaseremove salt water, dirt, etc. When possible, soak the watch in fresh
the setting or B to decrease it.water overnight to make sure that all salt is removed.
? When the 12/24-hour setting is selected, press C to toggle between
12-hour (12H) and 24-hour (24H) timekeeping.
4. Press A to return to the current time screen.
Notes
? The day of the week is automatically displayed in accordance with the
date (year, month, and day) settings.
? The year can be set in the range of 1995 to 2039.
? The watchOs built-in full automatic calendar automatically make allowances
for different month lengths and leap years. Once you set the date, there
should be no reason to change it except after the replacement of the
watchOs battery. |