2016-4
Using the Countdown TimerMoving the watch to a position that is parallel to the ground and then
Press C while in the Countdown Alarm Mode to start the countdown timertilting it towards you more than 40 degrees causes the backlight to light..
? When the end of the countdown is reached and auto-repeat is turned off,
the alarm sounds for 10 seconds or until you stop it by pressing any
button. The countdown time is automatically reset to its starting value
More
after the alarm stops.Parallel tothan
? Press C while a countdown operation is in progress to pause it. Pressground40°
C again to resume the countdown.
? To completely stop a countdown operation, first pause it (by pressing
C), and then press A. This returns the countdown time to its starting
value.
Turning Auto-repeat On and OffWarning!
? Never try to read your watch when mountain climbing or hiking in
1. In the Countdown Alarm Mode, hold down
areas that are dark or in areas with poor footing. Doing so is
ABA until the hours digit of the countdown timedangerous and can result in serious personal injury.
starts to flash.
2. Press B to turn auto-repeat on (AUTO? Never try to read your watch when running where there is danger of
accidents, especially in locations where there might be vehicular
displayed) and ofAUTf (O not displayed).
MAUTOC3. Press A to return to the countdown alarmor pedestrian traffic. Doing so is dangerous and can result in serious
personal injury.
display screen.
? Never try to read your watch when riding on a bicycle or when
? When the end of the countdown is reached and auto-repeat is turnedoperating a motorcycle or any other motor vehicle. Doing so is
on, the alarm sounds, but the countdown starts again automaticallydangerous and can result in a traffic accident and serious personal
whenever the countdown reaches zero. You can stop timing byinjury.
pressing C, and manually reset to the starting countdown time by? When you are wearing the watch, make sure that its auto light switch
pressing A.is turned off before riding on a bicycle or operating a motorcycle or
? Normally, an alarm tone sounds for 10 seconds when the end of theany other motor vehicle. Sudden and unintended operation of the
countdown is reached. If you use auto-repeat with start time of 10auto light switch can create a distraction, which can result in a traffic
seconds or less, the watch beeps once.accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down B for two seconds to turn the auto
light switch on (AUTO displayed) and ofAUTOf ( not displayed).
STOPWATCH MODE
? In order to protect against running down the battery, the auto light switch is
1/100 secondThe Stopwatch Mode lets you measure elapsedautomatically turned off approximately six hours after you turn it on. Repeat
the above procedure to turn the auto light switch back on if you want.
time, split times, and two finishes. The range of
Mode indicator? The auto light switch on indicator (AUTO) is on the display in all modes
the stopwatch is 23 hours, 59 minutes, 59.99
while the auto light switch is turned on.
seconds.
AB
REFERENCE
MC
This section contains more detailed and technical information about watch
Hours : Minutes
operation. It also contains important precautions and notes about the various
Secondsfeatures and functions of this watch.
(a) Elapsed TimeGraphic Area and Text Area
CCJJCJCJAText area?The graphic area shows the passage of
StartStopRe-startStopClearminutes in the Timekeeping, Dive Time
Graphic area
Measurement, Site, Countdown Alarm, and
(b) Split TimeStopwatch Modes, and the Log Data screen.
ABA segment appears in the graphic area each
CAJJAJCJA
time five minutes pass.
StartSplitSplit releaseStopClear
P? The text area can show up to four characters,
so longer text scrolls continually from right to
C
(c) Two FinishesMleft.
CAJJCJAJA
StartSplitStopSplit releaseClearAuto Return Feature
First runnerSecond runner finishes.Record time of? After you perform an operation in any mode (except for the backlight
finishes.Record time of firstsecond runner.operation), pressing M returns to the Timekeeping Mode.
runner.? If you leave a screen with flashing digits or cursor on the display for two
or three minutes without performing any operation, the watch automatically
saves anything you have input up to that point and exits the setting screen.
? If you leave the watch in Site and Identification Modes for about one
BACKLIGHThour without performing any operation, it automatically changes to the
Timekeeping Mode.
Auto light switchThe backlight uses an EL (electro-luminescent)
on indicatorpanel that causes the entire display to glow forData and Setting Scrolling
easy reading in the dark. The watchOs auto lightThe B and C buttons are used in various modes and screens to scroll
switch automatically turns on the backlight when
ABthrough data on the display. In most cases, holding down these buttons
you angle the watch towards your face.during a scroll operation scrolls through the data at high speed.
? The auto light switch must be turned on
PAUTO
(indicated by the auto light switch on indicator)12-hour/24-hour Timekeeping Formats
MCfor it to operate.The 12-hour/24-hour timekeeping format you select in the Timekeeping
Mode is also applied in the Dive Time Measurement, Site, and Alarm Modes.
Turning on the Backlight manually? With the 12-hour format, the P (PM) indicator appears to the left of the
In any mode, press B to illuminate the display for about two seconds.hour digits for times in the range of noon to 11:59 pm. No indicator is
? The above operation turns on the backlight regardless of the currentshown from midnight to 11:59 am.
auto light switch setting.? With the 24-hour format, times are indicated in the range of 00:00 to
23:59, with 24 indicator.
About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on for aboutTimekeeping Mode Notes
two seconds, whenever you position your wrist as described below in any? The day of the week is automatically displayed in accordance with the
mode.year, month, and day settings.
? See OBacklight Precautions� for other important information about using? The year can be set in the range of 1995 to 2039.
the backlight.? The watchOs built-in full automatic calendar automatically make allowances
for different month lengths and leap years. Once you set the date, there
should be no reason to change it except after the replacement of the
watchOs battery. |
ACEC
